Equipment
How to create your own custom-stamped wedges
Like so many other readers here on GolfWRX, I eagerly look forward to PGA Tour WITB photos each week. One of the most interesting aspects of Tour bags for me (and especially at the Waste Management Open) has always been the custom-stamped wedges and irons, like Pat Perez wedge pictured above. Custom stamping is no longer just for the Tour, however.
Cleveland, Mizuno and Vokey offer different options as well as initial stamping on their wedges and this year Nike is offering it on its irons. But, like many other at-home projects, it’s just so much more satisfying to do it yourself. Let these pictures be a guide to getting started. It’s easier (and could be cheaper) than you think!
Materials
- Stamping kit: Harbor Freight $9.99, Amazon.com $15 to $100.
- Hammer/Mallet: I have a 4-pound mallet and found that to be the most effective.
- Tape: Double-sided and masking.
- Paint (Optional).
Setup
The goal here is to firmly secure the club face to a hard surface. If you have access to a vise, you are in business as most vises have an anvil. If not, just make sure that the clean club face is firmly secured with double-sided tape. You may need someone to hold the club head securely in place while you swing the mallet, which is not as dangerous as it sounds.
Stamping
Identify the area you want to stamp and cover it with masking tape. This serves three purposes: you are able to draw reference lines with a straight edge to make your stamping neat, the imprint shows better on the tape so you can re-align your stamp for successive strikes and the tape absorbs some of the blow, making it less likely that the stamp will “bounce” and create a second impression on the wedge.
Take note of how far apart you are spacing consecutive letters as most first-time projects end up looking a bit like this: “G O L FW R X”
Let’s face it: some guys are better with a hammer than others. If you can make a confident swing at the stamp and create a deep imprint with just one swing then good for you! If not, it’s OK to take multiple swings. In fact, you’ll see Scotty Cameron doing just that if you watch this video from his website. According to Cameron, deeper strikes look “more finished … thin looks dainty and weak.” From my own experience, I have learned it is best to oscillate the stamping pin so that each successive strike drives the stamp from different angles to ensure that the stamping is symmetrical and deep.
Now bask in the glory of your very own “Tour” golf club! Obviously, this will take a little bit of practice. In the spirit of “measure twice, cut once,” you should probably try making a few practice stamps on an old club first. Keep in mind that forged clubs will be much more receptive to stamping than cast ones. Even with the cheaper Harbor Freight stamping kit, I still have not come across a wedge that is “unstampable” though.
Paint is optional and a great way to further customize your clubs. You can find many posts in the forums detailing different user methods. If nothing else, it most certainly brings a smile to my face when I look down in my bag to grab my DIY custom-stamped golf clubs.
- LIKE131
- LEGIT20
- WOW14
- LOL14
- IDHT7
- FLOP7
- OB6
- SHANK23
Equipment
A shocking Backstryke putter appearance + 7 interesting gear photos from the Zurich Classic
Welcome to New Orleans, where TPC Louisiana plays host to the 2024 Zurich Classic. In between breakfast beignets and nightly Creole feasts, PGA Tour players are also competing in the unique two-man format at the Zurich this week.
Although the vibes in Nawlins are a bit lighter-fare than the recent back-to-back competitions the Masters and the RBC Heritage signature event), the gear news was no less serious this week.
We spotted some recent changes from Rory McIlroy, a very rare Odyssey Backstryke putter, dove into the bag of legendary New Orleans Saints quarterback Drew Brees, and spotted Patrick Cantlay continuing to test new equipment.
Get your beads out and crack your crawfish, because it’s time for an equipment rundown from The Big Easy (meaning New Orleans, of course, not Ernie Els).
See all of our photos from the Zurich Classic here
Rory’s on-and-off lob wedge
Since the end of 2023, Rory McIlroy has had an on-again, off-again relationship with a Titleist Vokey K-Grind lob wedge. In his last start, it was on, and the wedge is back in the bag again this week. We got a great look at the complicated grind that McIlroy uses.
View this post on Instagram
A full look into McIlroy’s bag above also shows that he switched out of the TaylorMade BRNR Mini Copper that he used at the RBC Heritage, and he’s back into the Qi10 core 3-wood. As we discussed last week, McIlroy will likely keep the BRNR around as a course-specific club, trading it in and out for the 3-wood.
See Rory McIlroy’s full 2024 WITB from the Zurich here
Turning Back the clock
Unless Tommy Gainey is in the field, it’s unlikely you’ll ever see Odyssey’s Backstryke technology make an appearance on the PGA Tour.
But then, when you least expect it, Russ Cochran shows up.
For more than a decade – since the 2013 Sony Open in Hawai’i – Cochran has been stuck on 599 PGA Tour starts. This week will be his 600th.
Cochran is in the field at the Zurich this week playing alongside Eric Cole, whose regular caddie is Reed Cochran, Russ’s son.
The Backstryke putter was first released back in 2010, and its unique design helps shift the axis point of the putter closer to the CG of the head. And, the putter is getting a nod this week at the Zurich Classic, thanks to Cochran’s 600th career PGA Tour start.
The putter is certainly awesome, but don’t forget to check out Cochran’s full WITB from this week.
Drew Brees with a Super Bowl winning Scotty Cameron putter
Drew Brees, a legendary retired quarterback for the hometown New Orleans Saints, made an appearance at the Zurich’s Wednesday Pro-Am, playing alongside Zach Johnson, Ryan Palmer, and current Saints QB Derek Carr.
Brees’ bag included a TaylorMade Stealth2 Plus driver, a BRNR Mini 13.5-degree, a Stealth 5-wood, a mixed set of P-790 and P-760 irons, Milled Grind Hi-Toe wedges, and a custom Scotty Cameron “New Orleans Saints” putter, which Scotty made for Brees following his Super Bowl MVP-winning performance in 2010.
View this post on Instagram
It should also be noted that Brees has his Venmo QR code as a bag tag.
If you’re gambling with Brees on the course, just know that not having cash won’t work as an excuse.
Brilliant.
See Drew Brees’ full WITB from the Zurich here
Stricker’s unrecognizable putter
Steve Stricker has made numerous upgrades to his bag recently, including a new TSR3 driver and T100 irons, but his longtime Odyssey White Hot No. 2 putter is still going strong. It’s the most recognizable unrecognizable putter ever.
Here’s a better look at Stricker’s flatstick, which he started using back in 2007.
View this post on Instagram
Patrick Cantlay has opened the equipment-switching floodgates
Over on the PGA Tour’s Equipment Report this week, we covered Cantlay’s recent switch into Ping Blueprint S irons, and a Titleist TSR2 driver.
Cantlay hadn’t switched irons for about seven years, so the iron switch he made at The 2024 Masters came as a shock to the norm. He simply isn’t one to change gear very often, so anytime Cantlay makes a switch, it’s news.
It seems the floodgates of equipment testing have opened up a bit for Cantlay, who was also spotted testing a custom Scotty Cameron blade putter on Tuesday this week. By Wednesday, Cantlay was back practicing with his familiar Scotty Cameron T5 Proto mallet, but it’s certainly something to keep an eye on going forward.
Daniel Berger’s custom Jailbird site lines
Berger, who’s currently using Odyssey’s Ai-One Mini Jailbird mallet putter, has a unique 3-dot, 2-line alignment on the crown of his navy-white-navy-white mallet putter. Looking down at the putter, it’s easy to see why this alignment system would help; it just seems impossible to set up to the ball off-center, or misaligned to the target.
Also, for anyone worried, you can rest easy. Yes, he’s still playing the 2013 TaylorMade TP MC irons, which we highlighted in our recent “Modern Classics: Old vs. New” video testing series.
FitzMagic teams back up
Brothers Matthew and Alex Fitzpatrick are teaming up once again at the Zurich this year, and Bettinardi Golf hooked them up with some festive “FitzMagic” headcovers to match this week.
See what else is in Alex Fitzpatrick’s WITB here
And, with that, we say goodbye to the Zurich Classic in New Orleans. Don’t forget to check out all of our photos from this week, including 30 unique photo galleries full of equipment photos.
We’ll see you next week in Texas for the 2024 CJ Cup Byron Nelson!
- LIKE8
- LEGIT0
- WOW0
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
Whats in the Bag
Alejandro Tosti WITB 2024 (April)
- Alejandro Tosti what’s in the bag accurate as of the Zurich Classic.
Driver: Srixon ZX5 Mk II LS (9.5 degrees @10.5)
Shaft: Project X HZRDUS T1100 75 6.5
3-wood: TaylorMade Qi10 Tour
Shaft: Project X HZRDUS Black 80 TX
Hybrid: TaylorMade Qi10 Tour Rescue (22 degrees)
Shaft: Project X HZRDUS Smoke Black RDX 6.5 100
Irons: Srixon ZX7 Mk II (4-PW)
Shafts: True Temper Dynamic Gold Mid Tour Issue X100
Wedges: Cleveland RTX6 ZipCore Tour Rack (50-10 MID, 54-10 MID, 58-10 MID, 60-06 LOW)
Shafts: True Temper Dynamic Gold Mid Tour Issue X100, S400
Putter: Scotty Cameron
Grips: Golf Pride MCC Plus4
Check out more in-hand photos of Alejandro Tosti’s WITB in the forums.
- LIKE2
- LEGIT0
- WOW0
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
Whats in the Bag
Drew Brees WITB 2024 (April)
View this post on Instagram
Driver: TaylorMade Stealth 2 Plus (10.5 degrees)
Mini driver: TaylorMade BRNR Mini Copper (13.5 degrees)
5-wood: TaylorMade Stealth Plus (19 degrees)
Irons: TaylorMade P790 (4-8, PW), TaylorMade P760 (9)
Wedges: TaylorMade MG Hi-Toe (52-09, 56-10, 60)
Putter: Scotty Cameron Select Newport 2 Prototype
Check out more in-hand photos of Drew Brees’ clubs here.
- LIKE1
- LEGIT0
- WOW0
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
-
19th Hole2 weeks ago
Dave Portnoy places monstrous outright bet for the 2024 Masters
-
19th Hole4 days ago
Justin Thomas on the equipment choice of Scottie Scheffler that he thinks is ‘weird’
-
19th Hole2 weeks ago
Tiger Woods arrives at 2024 Masters equipped with a putter that may surprise you
-
19th Hole4 days ago
‘Absolutely crazy’ – Major champ lays into Patrick Cantlay over his decision on final hole of RBC Heritage
-
19th Hole2 weeks ago
Two star names reportedly blanked Jon Rahm all week at the Masters
-
19th Hole1 week ago
Report: LIV Golf identifies latest star name they hope to sign to breakaway tour
-
19th Hole2 weeks ago
Neal Shipley presser ends in awkward fashion after reporter claims Tiger handed him note on 8th fairway
-
19th Hole1 week ago
Brandel Chamblee has ‘no doubt’ who started the McIlroy/LIV rumor and why
Gary
Jun 16, 2015 at 2:14 pm
Instead of using mallet would a impact driver work work?
Kevin
Dec 17, 2014 at 5:18 pm
I used to punch stamp my clubs but the results were not as good as I wanted. So after searching on the internet I found http://www.personaltouchsports.com These guys did amazing work. After going through them I would never punch stamp again!
Corey
Nov 8, 2014 at 1:29 pm
Where can I get that solid dot stamp and what’s the best way to fill in the stamps with paint
nik dallos
Feb 7, 2014 at 10:41 pm
I am embarrassed someone even had to give this tutorial. Next tip, how to tie laces on your shoes. And how to put new grips on your clubs! Man im a negative nantz. Feel free to swear at me and put me down.
melrosegod
Feb 7, 2014 at 4:31 pm
I have stamped a few wedges and I like the “not so clean look”. That said, layer 4 or 5 strips of masking tape to develop an indentation when you stamp. It will help you keep your die in place for multiple hits.
Tony
Feb 7, 2014 at 3:52 pm
Anyone tried this on Ping wedges? Specifically the Tour S’s.
Thx
Jon Deerman
Feb 6, 2014 at 12:43 pm
As a metal worker with stamping experience, I would suggest to practice your technique on an old club or scrap piece of metal. Many first timers (including myself at the beginning) will not place the stamp correctly, causing uneven stamps or even damage to the material itself. (This means you must take a grinder and remove material to take the “bad” stamp away, which could change the feel of your club) As all things with golf it comes with practice, so if you keep at it success will come. Just remember… don’t make your first stamp an attempt to do it on those new Vokey’s or Fourteens.
Eric Johnson
Feb 6, 2014 at 1:05 pm
Jon – good reminder. It was my experience that the spacing of the pins was difficult at first (instinctively I placed the stamps too far apart) and that the depth of the stamp was not uniform. It was when I struck the stamp from several different angles that I saw the best results. Any other suggestions from your experience?
Jon Deerman
Feb 6, 2014 at 2:37 pm
Don’t be afraid to swing the hammer harder then you think, it is steel and most of the time this is a problem leading to a dreaded double hit. (Same stamp, same location but slightly off) On ease of use, there are metal stamp holders which allow a number of pins(They very from size to price, ebay being the best source), will allow you to stamp it in one swing. You may have to go over a few of the stamps but it will be quicker. If there is a missed hit, rock the pin until it settles in the previous stamp, and rock it slightly to the unmarked area hitting it with the hammer. On spacing it is good to have a lined up one after the other method. The gaps between the pins are usually what size it is (1/8″ Stamp should have 1/8″ between letters). A cost effective approach is to put a light coat of removable metal paint marker (around $5) on the bottom of your pins, placing them where you would like to see them on your clubs. This should create a template for better spacing.
zack
Feb 5, 2014 at 6:03 pm
I have cleveland cg14 wedges and find them to be un-stampable. I was wondering if anybody has stamped a cg14 wedge before and can give me any tips
Eric Johnson
Feb 5, 2014 at 7:44 pm
Zack –
CG14 are the same wedges I use and have had success stamping them all (I have 5!). I would guess that your wedges are not set firmly enough in place or your hammer/mallet is not heavy enough.
Mark
Feb 5, 2014 at 4:34 pm
What size stamp should I buy? 1/8″ ?
Eric Johnson
Feb 5, 2014 at 5:58 pm
Yes 1/8″ is the size you normally see
John Moriarty
Feb 5, 2014 at 3:55 pm
You do not ruin the finish when you stamp into it. Also instead of masking tape us double sided tape where you are going to stamp. You can press the stamp in by hand first and it leaves a mark of the letter. It allows you to plan out a bit better. Also when you hammer away the stamp won’t slip since it’s held down by the tape.
Roberat Upton
Feb 5, 2014 at 2:52 pm
Frankly, that cheap square font on those punches looks amateurish, cheap and nasty to me ? Why would you want to de-value a relatively expensive club like that ?
Jack
Feb 6, 2014 at 3:09 am
Roberat, tons of golf pros have it done, so maybe we just want to be like them? I’ve not done it personally since it does affect the resale value.
Nate
Feb 7, 2014 at 4:16 pm
When I did mine I purchased a Comic Sans set of stamps instead of the block font (believe its Courier). There are also some design stamps people might find interesting, like a bird or clover. My vokeys get a clover for each chip-in or hole-out.
Anthony H Melia
Dec 27, 2020 at 10:22 am
Great idea, like a college football helmet! I’m stealing this.
Monster
Mar 30, 2014 at 8:59 am
Roberat, It is meant to look that way. Its personal, A wedge is to be used until the grooves are gone. They are not for real sale. Next time you’re working on the game, Put your driver down and Go practice some wedges.
Chris
Feb 5, 2014 at 2:50 pm
I always love the phrase “it is not as dangerous as you would think”
Kevin Hefner
Feb 5, 2014 at 2:33 pm
What happens to the plating on the wedge, if it is chrome plated or a black wedge?
Eric Johnson
Feb 5, 2014 at 3:03 pm
Kevin – I have had no wear issues stamping chrome plated and raw clubs. I personally have not stamped any darker finished clubs but cannot foresee any danger to the club’s integrity. If you’re worried about rust then I’d be sure to fill in your stamps with paint. Good luck with your “wedged” haha