Connect with us

Equipment

Review: Ben Hogan Ft. Worth 15 irons vs. Hogan irons of old

Published

on

Hogan irons

The Ben Hogan Company returned to the golf equipment business with the introduction of its Ft. Worth irons in January. We detailed the release at the time, and a bevy of reviews have populated the internet in the time since.

Let’s recap the Ft. Worth marketing literature and features.

The Ft. Worths (and TK Wedge) come in 44 loft options from 20 to 63 degrees. While it may take some getting used to, the company’s slogan, “precision is back,” is driven home by the arrangement.

The irons are forged from 1025 carbon steel and feature the V Sole design developed by company CEO Terry Koehler, which maximizes playability from any lie, according to the company, thanks to a high-bounce leading edge and lower-bounce sole.

Also visually apparent and a centerpiece feature of the irons: perimeter weighting.

Again, we wondered how the new Hogans would stack up against some of the great Hogan irons from the past 50 years. Further, we wondered how those irons compared to one another. How would, say, the Power Thrust iron of the early 60s compare to the 1999 Apex?

7

(L-R) Irons 1, 2, 3, 4, 5 listed below

The irons we tested

  1. Power Thrust (1962)
  2. Apex II (1979)
  3. Apex Redline (1988)
  4. Apex (1999)
  5. Ft Worth
3

From the Power Thrust (1962) to the Ft Worth (2015)

The lengths, lie, lofts were all within a degree of each other (30-31), standard length (37.50 inches – with the Power Thrust, despite being a 5 iron, 0.5-inches shorter) and standard lie of 60 degrees on all.

In our testing, conducted on an outdoor driving range with 5-10 mph of wind and using a TrackMan to record the data, the Ft. Worth irons were longer, generally higher flying, generally more precise, and at least as efficient as any other Hogan iron in terms of smash factor.

Conducting the testing, your intrepid writer and a pair of Class A PGA pros.

Screen Shot 2015-09-03 at 4.07.49 PMDispersion graphics

Screen Shot 2015-08-31 at 5.45.07 PM

David’s dispersion

Screen Shot 2015-08-31 at 5.44.47 PM

Jeff’s dispersion

Screen Shot 2015-08-31 at 5.44.36 PM

Ben’s dispersion

The Hogan Company also did its own testing using 15 golfers with club speeds from the mid-70s to the mid-90s. In all of the company’s tests, the Ft. Worth was either the longest or second-longest club.

For the single-digit handicapper, the club represents a modest improvement over the previous iron models. For the mid-handicapper, however, it’s a playable forged iron, as the data indicates.

4

The Ft. Worth possessed a more solid feeling strike and a significant amount of feedback, all while performing better than expected on off-center hits. Enthusiasts will definitely see and feel the similarities between the Ft. Worths and the most recent Hogan Apex. However, they’ll also likely see better performance on the launch monitor and plenty of workability on course.

The player will certainly feel any misses, but won’t get the hand-numbing sting of older blades. Good, solid sound, and soft feel on center strikes. Great turf interaction, especially on steeper swings (thanks V Sole).

5

There’s no doubt these clubs mark a step forward for the Hogan Company and open cast a wider net for potential players.

A forged blade iron may be a difficult sell in an environment where the best golfers in the world are playing multi-material clubs. However, if you’re a purist and/or a Hogan disciple, don’t hesitate to go through the HoganFit process.

[wrx_retail_links productid=”22″]

Your Reaction?
  • 221
  • LEGIT32
  • WOW24
  • LOL7
  • IDHT0
  • FLOP4
  • OB5
  • SHANK19

GolfWRX Editor-in-Chief

30 Comments

30 Comments

  1. iSeeClearly

    May 22, 2018 at 12:28 am

    “…an environment where the best golfers in the world are playing multi-material clubs.”
    …or an environment where the best golfers in the world are selling multi-material clubs. Ya think??!!!

  2. Panther73

    Sep 9, 2016 at 6:31 pm

    I would really like to find my first Hogan set, Apex II, Apex 5 shaft, 2-Pw Black filled Cameo. The one thing to change would be CC grooves, the original sets were V grooves, Hogan Balata balls had super thin covers. Same thing now with ball covers softer to match up with current groove regulations. Any ideas? Fly to Japan to Miura and recreate them?

  3. Billy Bondaruk

    Jan 15, 2016 at 9:39 pm

    I first played Hogan Irons in the 70’s in High School and jr. Golf. My dad was a state am champ and he played them… Every few years we would get a new set and I’d take his, until the apex set cam put….. We both played them and I had a great year playing so did he….. Last year I went the PGA Show, with out my Dad… He’s gone now….. But the feeling of hitting a Ben Hogan iron…. That Hogan Apex iron the one we bothe bought that year back in the 1980’s…. I found it at last years show, but it was better…. Much better and it was a shock that that was even possible. Couple that with the history and the hero that you loved thru life, his stories and jokes…. What the man stood up for in this game….. I bought two sets. The 21 degree iron my friends call it the sniper rifle. I have never had an easier 3 iron to hit….. You fell the speed off the face. Carve it anyway you want. And the tradition to keep lofts at least close to what they should be….. Com om Man…… Hogan was the a man that changed golf

  4. Dave

    Oct 20, 2015 at 2:44 am

    My first full set of irons was a used set of apex irons, with some powerbilt persimmons, some 30+ yrs ago. Looked great but not very forgiving. Still to this day at address, I like the look of a straight sole line and not too thick a top line.

  5. Peter Whitford

    Oct 8, 2015 at 2:35 pm

    I played Hogan Apex’s with a # 4 Hogan shaft–loved those blades. I had them refinished and restored 3 times–they finally wore out unfortunately. I am interested in these but they don’t have any shaft options to speak of. I now play Titleist 710 MB’s with a Project X 5.5 Shaft–I would switch to these in a heartbeat if they could put a decent shaft in them–KBS isn’t that great a shaft.

    • JP Sourdellia

      Oct 14, 2015 at 12:41 pm

      Peter – You can order your Ft. Worth 15 irons with the Project X 5.5 shaft, if that’s your preference. We offer a wide selection of custom shafts and I’m sure we can accommodate your needs. Please call our customer service line to speak with one of our experts. 844-53-HOGAN(46426)

  6. Walt Pendleton

    Oct 6, 2015 at 3:06 pm

    I have just three words to say about the new Hogan irons I just bought…smallest dispersion ratio! It’s all about the misses, gentlemen! We all create them.

  7. Mark

    Oct 5, 2015 at 8:52 pm

    Regardless of outcome, that is a timeless lineup. Pure class.

  8. Brian K

    Oct 5, 2015 at 2:52 pm

    Did each iron have the original stock shaft or reloaded with the same shaft? Wouldn’t the original shafts in power thrust, Apex II and Apex 88 be too worn and degraded to make and accurate comparsion?

  9. Carlos Danger

    Oct 5, 2015 at 11:12 am

    I have a set of the 89 Apex sitting in my office looking clean and pretty. I grew up with them and have always wished Hogan would make a comeback…so needless to say I was pretty excited to see the Ft Worth come out. I love the website process of building them out and of course they look beautiful.

    However, I think I will wait to order them until a cavity back or slightly larger iron head is released. At this point in my life, trying to hit a 4 iron blade is just not all that enticing. Im currently playing Adams CMBs (which are not terribly far off from a blade) so if Hogan releases something slightly bigger I dont think I could stop myself from ordering a mixed set.

    • John C

      Oct 5, 2015 at 9:54 pm

      You like Hogan.. Just get the Lofts that are 6 Iron and down.. Worth it.. Why wait if Hogan is your favorite..

      • Carlos Danger

        Oct 6, 2015 at 9:25 am

        to be clear…the thought of beautiful Hogan blades in my bag is my favorite. the reality of trying to hit a blade 4 iron consistently is another thing.

        Im sure they will expand and make a slightly bigger iron, by then I will be due for some new ones:)

  10. rex235

    Oct 5, 2015 at 3:09 am

    RH ONLY.

  11. barf

    Oct 4, 2015 at 12:55 pm

    Were the shafts standardized for this test? The shafts alone in the older clubs make the comparison lopsided.

  12. Jamie

    Oct 3, 2015 at 11:14 am

    You can really see the influence of SCOR clubs. I guess same owners!

  13. mhendon

    Oct 3, 2015 at 10:25 am

    I got to say that’s an extreme release cycle there. 17 years followed by 11 and 11

  14. birly-shirly

    Oct 2, 2015 at 6:04 pm

    Kudos for carrying out the test, but does it really mean anything? Ignore the scatter graphics, and what is the data saying?
    Smash factor – 2 out of 3 testers saw no advantage to the new club.
    Spin – 2 out of 3 testers got more spin from older clubs.
    Height – 2 out of 3 testers hit older clubs higher.
    Landing angle – all 3 testers had older clubs landing steeper.
    I’m not saying that proves the older clubs are better. I am asking what conclusions can you really draw from this? Is this a test of how the clubs perform, or the swings the testers made?

    • billm311

      Oct 4, 2015 at 8:02 pm

      I currently play with Hogan anniversary blades, dynamic gold shafts. I used the hogan demo pack to test the new irons head to head with mine. Though the lofts were not exact matches, the biggest difference for me was shaft used. I’d like to try them again with matching shaft and length of shaft. In the end, I did really enjoy the new club. Very clean look, slightly thicker and rounder than my current blades, but produced very nice results.

      In the end, I did not make the switch. My clubs are custom fit, so they feel perfect to me. A little extra forgiveness would be nice – for that reason, I am considering getting just 4, maybe 5 iron replacements with slightly different loft spacing.

      Well designed club if you are looking at forged blades, just make sure to get the right shaft for you!

      • HR

        Oct 5, 2015 at 12:45 am

        Well at $149 per club, it ain’t cheap. With no custom shaft options, it’s highway robbery

        • JP Sourdellia

          Oct 14, 2015 at 12:45 pm

          HR – We do offer a large selection of custom shafts. You can call one of our experts at 844-53-HOGAN(46426) to discuss what shaft options we offer. I’m sure we can accommodate your needs.

  15. cbails00

    Oct 2, 2015 at 5:25 pm

    I think this is a fantastic exercise and cool to see how Hogan compares to Hogan. I would be curious how the new Hogan Ft. Worth 15 irons would stand up in a similar test against the new multi-material irons – 716 AP2, new Apex Pro’s, TM PSi, Ping i Series etc. If the results were good for the Ft. Worth 15’s it might make them more appealing to purchase.

  16. Bogeypro

    Oct 2, 2015 at 5:19 pm

    I just feel that it is completely confusing to not put an iron number. I don’t want to have to remember the loft. Just say, 6 iron, not 31 or whatever it is…

  17. michael

    Oct 2, 2015 at 4:19 pm

    I play the apex ii plus and I love them had the lofts tweaked a bit due to my slower swing speed but they feel great. Love the feel of forged irons.

  18. Joe

    Oct 2, 2015 at 3:22 pm

    I play the Hogan Apex 1999 model, love them. Also, am selling a refinished Hogan Apex 1999 model in the classified.

    I much refer these to the current Apex by Callaway.

  19. RB

    Oct 2, 2015 at 1:37 pm

    The spreadsheet descriptions for the irons should match the descriptions at the start of the review. And in the same order. It’s quite confusing which Apex is which. Consistency would help.

    • Cliff

      Oct 2, 2015 at 3:17 pm

      it’s not THAT difficult to follow!

    • Rich

      Oct 2, 2015 at 9:28 pm

      I agree it should be more consistent at a glance. If you take a few minutes, you can figure out which one is which. Not very well done though in regards to ease of understanding.

  20. BS

    Oct 2, 2015 at 12:25 pm

    I see no similarities at all. That is BS

  21. Craigar

    Oct 2, 2015 at 11:51 am

    Just out of curiosity what were the differences in shafts as far as frequency?

  22. TR1PTIK

    Oct 2, 2015 at 11:22 am

    I learned how to play golf with an old set of blades, and prefer a more classic looking club despite my higher handicap. I’d love to give these irons a try sometime.

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Equipment

Coolest thing for sale in the GolfWRX Classifieds (4/26/24): Artisan 0521 custom putter

Published

on

At GolfWRX, we are a community of like-minded individuals that all experience and express our enjoyment of the game in many ways.

It’s that sense of community that drives day-to-day interactions in the forums on topics that range from best driver to what marker you use to mark your ball. It even allows us to share another thing we all love – buying and selling equipment.

Currently, in our GolfWRX buy/sell/trade (BST) forum, there is a listing for an Artisan 0521 custom putter

From the seller: (@Nobody2): “$775 -Artisan 0521 custom putter PVD (black finish) with sweep neck hosel.  There are no personal stampings other than my player # in very small print on the side of the hosel (all Artisan products have this along with the date it was made). This putter looks absolutely amazing and has only been used for 3 rounds. It has a black steel shaft and has a very Cam Smith look to it.  The putter looks new and has no wear marks anywhere on the putter.  It comes with extra weights (one set of of 5 gram weights and one set of 15 gram weights). The head cover is a a navy blue ‘quilted blade putter cover.’  If you are wondering why I am selling…I flat out have the yips and the only thing saving me is a broomstick.  New, this putter is $1085, so if the specs work for you (grip, length and lie can certainly be tweaked) it will save you some good money and 2 month wait time.

Specs:

Loft               2.75  degrees
Lie                  69  degrees
Length           35.25″
offset             .300 slightly less than full shaft offset
head weight     350 grams
Toe Hang          20 degrees
Grip                   Ionic Classic Pistol”

To check out the full listing in our BST forum, head through the link: Artisan 0521 custom putter

This is the most impressive current listing from the GolfWRX BST, and if you are curious about the rules to participate in the BST Forum you can check them out here: GolfWRX BST Rules

Your Reaction?
  • 1
  • LEGIT0
  • WOW0
  • LOL0
  • IDHT0
  • FLOP0
  • OB0
  • SHANK0

Continue Reading

Equipment

A shocking Backstryke putter appearance + 7 interesting gear photos from the Zurich Classic

Published

on

Welcome to New Orleans, where TPC Louisiana plays host to the 2024 Zurich Classic. In between breakfast beignets and nightly Creole feasts, PGA Tour players are also competing in the unique two-man format at the Zurich this week.

Although the vibes in Nawlins are a bit lighter-fare than the recent back-to-back competitions the Masters and the RBC Heritage signature event), the gear news was no less serious this week.

We spotted some recent changes from Rory McIlroy, a very rare Odyssey Backstryke putter, dove into the bag of legendary New Orleans Saints quarterback Drew Brees, and spotted Patrick Cantlay continuing to test new equipment.

Get your beads out and crack your crawfish, because it’s time for an equipment rundown from The Big Easy (meaning New Orleans, of course, not Ernie Els).

See all of our photos from the Zurich Classic here

Rory’s on-and-off lob wedge

Since the end of 2023, Rory McIlroy has had an on-again, off-again relationship with a Titleist Vokey K-Grind lob wedge. In his last start, it was on, and the wedge is back in the bag again this week. We got a great look at the complicated grind that McIlroy uses.

 

View this post on Instagram

 

A post shared by GolfWRX (@golfwrx)

A full look into McIlroy’s bag above also shows that he switched out of the TaylorMade BRNR Mini Copper that he used at the RBC Heritage, and he’s back into the Qi10 core 3-wood. As we discussed last week, McIlroy will likely keep the BRNR around as a course-specific club, trading it in and out for the 3-wood.

See Rory McIlroy’s full 2024 WITB from the Zurich here

Turning Back the clock

Unless Tommy Gainey is in the field, it’s unlikely you’ll ever see Odyssey’s Backstryke technology make an appearance on the PGA Tour.

But then, when you least expect it, Russ Cochran shows up.

For more than a decade – since the 2013 Sony Open in Hawai’i – Cochran has been stuck on 599 PGA Tour starts. This week will be his 600th.

Cochran is in the field at the Zurich this week playing alongside Eric Cole, whose regular caddie is Reed Cochran, Russ’s son.

The Backstryke putter was first released back in 2010, and its unique design helps shift the axis point of the putter closer to the CG of the head. And, the putter is getting a nod this week at the Zurich Classic, thanks to Cochran’s 600th career PGA Tour start.

The putter is certainly awesome, but don’t forget to check out Cochran’s full WITB from this week.

Drew Brees with a Super Bowl winning Scotty Cameron putter

Drew Brees, a legendary retired quarterback for the hometown New Orleans Saints, made an appearance at the Zurich’s Wednesday Pro-Am, playing alongside Zach Johnson, Ryan Palmer, and current Saints QB Derek Carr.

Brees’ bag included a TaylorMade Stealth2 Plus driver, a BRNR Mini 13.5-degree, a Stealth 5-wood, a mixed set of P-790 and P-760 irons, Milled Grind Hi-Toe wedges, and a custom Scotty Cameron “New Orleans Saints” putter, which Scotty made for Brees following his Super Bowl MVP-winning performance in 2010.

 

View this post on Instagram

 

A post shared by GolfWRX (@golfwrx)

It should also be noted that Brees has his Venmo QR code as a bag tag.

If you’re gambling with Brees on the course, just know that not having cash won’t work as an excuse.

Brilliant.

See Drew Brees’ full WITB from the Zurich here

Stricker’s unrecognizable putter

Steve Stricker has made numerous upgrades to his bag recently, including a new TSR3 driver and T100 irons, but his longtime Odyssey White Hot No. 2 putter is still going strong. It’s the most recognizable unrecognizable putter ever.

Here’s a better look at Stricker’s flatstick, which he started using back in 2007.

 

View this post on Instagram

 

A post shared by GolfWRX (@golfwrx)

Patrick Cantlay has opened the equipment-switching floodgates

Over on the PGA Tour’s Equipment Report this week, we covered Cantlay’s recent switch into Ping Blueprint S irons, and a Titleist TSR2 driver.

Cantlay hadn’t switched irons for about seven years, so the iron switch he made at The 2024 Masters came as a shock to the norm. He simply isn’t one to change gear very often, so anytime Cantlay makes a switch, it’s news.

It seems the floodgates of equipment testing have opened up a bit for Cantlay, who was also spotted testing a custom Scotty Cameron blade putter on Tuesday this week. By Wednesday, Cantlay was back practicing with his familiar Scotty Cameron T5 Proto mallet, but it’s certainly something to keep an eye on going forward.

Daniel Berger’s custom Jailbird site lines

Berger, who’s currently using Odyssey’s Ai-One Mini Jailbird mallet putter, has a unique 3-dot, 2-line alignment on the crown of his navy-white-navy-white mallet putter. Looking down at the putter, it’s easy to see why this alignment system would help; it just seems impossible to set up to the ball off-center, or misaligned to the target.

Also, for anyone worried, you can rest easy. Yes, he’s still playing the 2013 TaylorMade TP MC irons, which we highlighted in our recent “Modern Classics: Old vs. New” video testing series.

FitzMagic teams back up

Brothers Matthew and Alex Fitzpatrick are teaming up once again at the Zurich this year, and Bettinardi Golf hooked them up with some festive “FitzMagic” headcovers to match this week.

See what else is in Alex Fitzpatrick’s WITB here

And, with that, we say goodbye to the Zurich Classic in New Orleans. Don’t forget to check out all of our photos from this week, including 30 unique photo galleries full of equipment photos.

We’ll see you next week in Texas for the 2024 CJ Cup Byron Nelson!

Your Reaction?
  • 8
  • LEGIT0
  • WOW0
  • LOL0
  • IDHT0
  • FLOP0
  • OB0
  • SHANK0

Continue Reading

Whats in the Bag

Alejandro Tosti WITB 2024 (April)

Published

on

  • Alejandro Tosti what’s in the bag accurate as of the Zurich Classic.

Driver: Srixon ZX5 Mk II LS (9.5 degrees @10.5)
Shaft: Project X HZRDUS T1100 75 6.5

3-wood: TaylorMade Qi10 Tour
Shaft: Project X HZRDUS Black 80 TX

Hybrid: TaylorMade Qi10 Tour Rescue (22 degrees)
Shaft: Project X HZRDUS Smoke Black RDX 6.5 100

Irons: Srixon ZX7 Mk II (4-PW)
Shafts: True Temper Dynamic Gold Mid Tour Issue X100

Wedges: Cleveland RTX6 ZipCore Tour Rack (50-10 MID, 54-10 MID, 58-10 MID, 60-06 LOW)
Shafts: True Temper Dynamic Gold Mid Tour Issue X100, S400

Putter: Scotty Cameron

Grips: Golf Pride MCC Plus4

Check out more in-hand photos of Alejandro Tosti’s WITB in the forums.

Your Reaction?
  • 2
  • LEGIT0
  • WOW0
  • LOL0
  • IDHT0
  • FLOP0
  • OB0
  • SHANK0

Continue Reading

WITB

Facebook

Trending