Every driver company boasts a couple technological advances with their new driver launches; maybe a new crown to save weight, an aerodynamic crown for more club head speed, a different sole design, a way to shift CG to dial in trajectory, higher MOI, or a different face technology. Cobra, on the other hand, has thrown the kitchen sink at its new King F9 Speedback drivers, checking off all of those boxes — even though aerodynamic designs are often detrimental to lowering CG.

Compared to popular technologies in today’s current driver market, according to Cobra, the new King F9 Speedback drivers are the only ones to check off all the boxes.

In general, Cobra’s King F9 Speedback drivers are designed to help achieve more club head speed with a more aerodynamic crown, coupled with a lower center of gravity (CG) to make the driver fly farther. How did Cobra accomplish that exactly?

Below, we’ll dive into some of the key technologies in its drivers that are listed above. Then, we will get into Cobra’s new King F9 Speedback and Speedback Tour fairway woods, as well.

All King F9 products are available on January 18, 2019. Click here for more in-hand photos.

Cobra King F9 Speedback drivers

What does Speedback mean? Speedback is the combination of Aerodynamic, or “Aeroficient” crown designs, and a sole structure designed to lower CG. PWR Ridges on the top of the driver crown work to reduce drag as the club head flies through the air in your downswing, thus increasing club head speed. Cobra also raised the “perimeter skirt, tail and crown” and rounded off the edges to further reduce drag. To lower CG in the club head after raising it to achieve those aerodynamic qualities, Cobra built a visible structure on the rear sole of the club head.

Related: Cobra’s King F9 Speedback irons and hybrids

Cobra’s King F9 Speedback drivers, with bodies and faces made from 8-1-1 Titanium, also have carbon fiber crowns that “wrap around” the bodies in order to save 10 grams of additional weight to be distributed lower in the club head. Here’s a look at that wrap-around design via Cobra graphics.

Cobra is once again CNC-milling its King F9 faces, as it did with the previous King Cobra F8 drivers, in order to help deliver more precise faces that allow the company to design them thinner and hotter due to tighter tolerances. Cobra says the new faces are 3 percent thinner and 10 percent lighter.

Additionally, due to improved bulge-and-roll, the drivers have different loft measurements across the face in order to help your golf ball curve back to the center line no matter where you hit the ball.

With new “E9 Speed Tuned technology,” Cobra also says it’s optimized the bottom and top roll curvatures of the face — the goal is to minimize the negatives of gear effect (slices and hooks), according to Cobra. In theory, that means strikes off the toe and heel would both curve back to the center line, instead of hooking or slicing too much.

To help golfers dial in launch, spin and draw/fade bias, the King F9 Speedback drivers have MyFly8 hosels (8 loft settings, with 3 draw settings) with the familiar Smart Pad to keep the driver sitting flat, and two weight ports on the sole that house either 14- or 2-gram weights to move weight forward or back. Here’s a look at the specs:

In the end, Cobra says its new F9 driver (9 degrees, back setting) produces 1 mph more ball speed than the F8+ driver, 450 rpm lower spin and 8.8 yards more distance.

Cobra’s new drivers (available in yellow and “avalanche” colorways) will sell for $449 with Cobra’s Lamkin Crossline grips, equipped with Cobra Connect powered by Arccos. Aftermarket shaft options include UST Mamiya Helium 50, Fujikura Atmos Tour Spec Blue, Fujikura Atmos Tour Spec Black 7 or the Project X HZRDUS Smoke 60.

Cobra King F9 Speedback and Speedback Tour fairways

Like the F9 drivers, the F9 fairway woods are designed to have lower CGs to help increase launch and ball speed. To achieve this, Cobra added a fixed, 15-gram Tungsten weight in the rear sole of the woods.

For better turf interaction, Cobra shallowed out the Baffler Rail heights in the lower-lofted woods (which require more of a sweeping motion) and taller rails on the higher-lofted woods (which typically require steeper/more varied angles of attack).

As with the drivers, the fairway woods also have aerodynamic crowns that have PWR Ridges for more clubhead speed, and carbon fiber crowns to save weight. For the first time on a Cobra fairway wood are also CNC-milled faces, which, according to Cobra, increases ball speeds by up to 2.5 mph compared to polished faces.

Each of the King F9 fairway woods ($269 apiece) also come with MyFly8 hosels to help dial in loft and trajectory biases. As you may expect, the King F9 Speedback Tour model has a more compact shape and has a forward CG for a more penetrating ball flight. Here are the specs for each below

King F9 Speedback Specs via Cobra

• Colors: Black/Yellow or Satin Black/Avalanche
• Grip: Lamkin Crossline (58+) Connect – Black
• Shaft Options: UST Mamiya Helium 60 or Fujikura Atmos Blue 7
• Available in RH (LH available in custom)

King F9 Speedback Tour Specs

• Colors: Satin Black
• Grip: Lamkin Crossline (58+) Connect – Black
• Shaft: Project X HZRDUS Smoke 70
• 3-4 wood available in RH (LH available in custom); 4-5 wood available in RH only.

Related: Cobra’s King F9 Speedback irons and hybrids

Bonus: Rickie Fowler and Bryson DeChambeau talk about the new driver (and in-hand pics of their clubs)

 

Click here to watch the full “What’s in the Bag?” video

Fowler’s new Cobra King F9 Speedback

See more photos and join the discussion about Rickie’s new driver

Bryson’s new Cobra King F9 Speedback driver

Related

• Bryson’s Cobra King F9 Speedback driver
• See what GolfWRX members are saying about the Cobra King F9 Speedback clubs in our forums