Equipment

Paint fill 101

Published

12 years ago

Jun 19, 2012

GolfWRX

By GolfWRX member HuckleBogey_Finn

To see the original thread the viral discussion in the forums click here

As promised, after much trial and error I believe I have found a very good way to paint fill golf clubs. I will try to be as detailed as possible and I am including a few pics. They were taken with my iphone so the pics arent great, but I am extremely happy with the results. I have tried many paints, solvents and dilutes and this is by far the best combination I have found. I feel anyone can do this. I am sure there are other ways to get good results but this is my preferred way

I appreciate constructive criticisms and feel free to ask questions.

I went with a SF Giants color scheme here. All of you dodger fans can suck it

First you need the tools. In this example I used Tamiya color paint in smoke, clear orange, clear red, and clear yellow. I also used testors model enamal for the top sight line. You will also need tal strip paint stripper, acetone nail polish remover, non-acetone nail polish remover, 91% rubbing alcohol, q-tips, toothpicks, towels, lint free rags, gloves (you don’t want paint stripper on your fingers!) an old toothbrush and PATIENCE!

To see the original thread the viral discussion in the forums click here

First thing you need to do is get rid of all the original paint. With a q-tip apply a liberal amount of tal strip to all painted areas. Wait 5-10 minutes and you will see blobs of paint bubbling out of the spaces.

To see the original thread the viral discussion in the forums click here

After all of the paint has bubbled out grab the toothbrush and in a sink you dont mind getting stained (or outside with the garden hose) scrub and rinse out all the spaces that had paint in them. The paint should come right out. Sometimes you may have a few remnants hanging around. If so reapply the stripper to these parts until you are left with only bare metal.

To see the original thread the viral discussion in the forums click here

Now take your acetone and give the whole head a good wash scrub. This will remove any oils or remnants of stripper and give you a nice clean surface for the paint. Let it all dry out and now its time to get to painting!

I first use a q-tip to apply a little of the rubbing alcohol to the spaces I’m going to paint. This thins the paint slightly to allow a nice glassy finish when it dries without bubbles. You just need the slightest sheen, not a puddle. This takes practice and it took me a few tries to get right. Now with a toothpick dipped in the paint start applying the paint into the spaces. The paint should “travel” to fill the spaces. If you go outside the lines a little bit thats ok, but start light then work your way thicker. When the paint starts to dry you will get a good feel for how it will finish. If you dont like the opacity, start over. Dont apply a coat over the first.

To see the original thread the viral discussion in the forums click here

The topline of the Kombi s was tough because of the angle. I decided on gloss white here for function over form.

To see the original thread the viral discussion in the forums click here

So now after all the paint is applied (depending on angles and position you may have to wait to do certain sections, but I recommend holding off on clean up until you are all done) you are going to have some over paint. No worries. Just let it all dry. This takes a while. Heat will help acrylic paints, but enamels only dry by oxidation and that takes time. I wait overnight.
After all the paint is dry grab a lint free cloth or used t-shirt and dip it into the non acetone remover. I use the non acetone here because it does the job without the fear of stripping the paint in the grooves. Using light pressure rub the moist rag over the over painted areas making sure not to get the cloth in the painted grooves until all the unwanted paint is gone.

Now you have a DIY custom club. The beauty of this is if you arent totally happy you can do it as many times as you want.
Enjoy the final product.

To see the original thread the viral discussion in the forums click here

Your Reaction?

LIKE20
LEGIT3
WOW2
LOL3
IDHT1
FLOP1
OB1
SHANK3

Equipment

A shocking Backstryke putter appearance + 7 interesting gear photos from the Zurich Classic

Published

18 hours ago

Apr 25, 2024

Andrew Tursky

Welcome to New Orleans, where TPC Louisiana plays host to the 2024 Zurich Classic. In between breakfast beignets and nightly Creole feasts, PGA Tour players are also competing in the unique two-man format at the Zurich this week.

Although the vibes in Nawlins are a bit lighter-fare than the recent back-to-back competitions the Masters and the RBC Heritage signature event), the gear news was no less serious this week.

We spotted some recent changes from Rory McIlroy, a very rare Odyssey Backstryke putter, dove into the bag of legendary New Orleans Saints quarterback Drew Brees, and spotted Patrick Cantlay continuing to test new equipment.

Get your beads out and crack your crawfish, because it’s time for an equipment rundown from The Big Easy (meaning New Orleans, of course, not Ernie Els).

See all of our photos from the Zurich Classic here

Rory’s on-and-off lob wedge

Since the end of 2023, Rory McIlroy has had an on-again, off-again relationship with a Titleist Vokey K-Grind lob wedge. In his last start, it was on, and the wedge is back in the bag again this week. We got a great look at the complicated grind that McIlroy uses.

View this post on Instagram

A post shared by GolfWRX (@golfwrx)

A full look into McIlroy’s bag above also shows that he switched out of the TaylorMade BRNR Mini Copper that he used at the RBC Heritage, and he’s back into the Qi10 core 3-wood. As we discussed last week, McIlroy will likely keep the BRNR around as a course-specific club, trading it in and out for the 3-wood.

See Rory McIlroy’s full 2024 WITB from the Zurich here

Turning Back the clock

Unless Tommy Gainey is in the field, it’s unlikely you’ll ever see Odyssey’s Backstryke technology make an appearance on the PGA Tour.

But then, when you least expect it, Russ Cochran shows up.

For more than a decade – since the 2013 Sony Open in Hawai’i – Cochran has been stuck on 599 PGA Tour starts. This week will be his 600th.

Cochran is in the field at the Zurich this week playing alongside Eric Cole, whose regular caddie is Reed Cochran, Russ’s son.

The Backstryke putter was first released back in 2010, and its unique design helps shift the axis point of the putter closer to the CG of the head. And, the putter is getting a nod this week at the Zurich Classic, thanks to Cochran’s 600th career PGA Tour start.

The putter is certainly awesome, but don’t forget to check out Cochran’s full WITB from this week.

Drew Brees with a Super Bowl winning Scotty Cameron putter

Drew Brees, a legendary retired quarterback for the hometown New Orleans Saints, made an appearance at the Zurich’s Wednesday Pro-Am, playing alongside Zach Johnson, Ryan Palmer, and current Saints QB Derek Carr.

Brees’ bag included a TaylorMade Stealth2 Plus driver, a BRNR Mini 13.5-degree, a Stealth 5-wood, a mixed set of P-790 and P-760 irons, Milled Grind Hi-Toe wedges, and a custom Scotty Cameron “New Orleans Saints” putter, which Scotty made for Brees following his Super Bowl MVP-winning performance in 2010.

View this post on Instagram

A post shared by GolfWRX (@golfwrx)

It should also be noted that Brees has his Venmo QR code as a bag tag.

If you’re gambling with Brees on the course, just know that not having cash won’t work as an excuse.

Brilliant.

See Drew Brees’ full WITB from the Zurich here

Stricker’s unrecognizable putter

Steve Stricker has made numerous upgrades to his bag recently, including a new TSR3 driver and T100 irons, but his longtime Odyssey White Hot No. 2 putter is still going strong. It’s the most recognizable unrecognizable putter ever.

Here’s a better look at Stricker’s flatstick, which he started using back in 2007.

View this post on Instagram

A post shared by GolfWRX (@golfwrx)

Patrick Cantlay has opened the equipment-switching floodgates

Over on the PGA Tour’s Equipment Report this week, we covered Cantlay’s recent switch into Ping Blueprint S irons, and a Titleist TSR2 driver.

Cantlay hadn’t switched irons for about seven years, so the iron switch he made at The 2024 Masters came as a shock to the norm. He simply isn’t one to change gear very often, so anytime Cantlay makes a switch, it’s news.

It seems the floodgates of equipment testing have opened up a bit for Cantlay, who was also spotted testing a custom Scotty Cameron blade putter on Tuesday this week. By Wednesday, Cantlay was back practicing with his familiar Scotty Cameron T5 Proto mallet, but it’s certainly something to keep an eye on going forward.

Daniel Berger’s custom Jailbird site lines

Berger, who’s currently using Odyssey’s Ai-One Mini Jailbird mallet putter, has a unique 3-dot, 2-line alignment on the crown of his navy-white-navy-white mallet putter. Looking down at the putter, it’s easy to see why this alignment system would help; it just seems impossible to set up to the ball off-center, or misaligned to the target.

Also, for anyone worried, you can rest easy. Yes, he’s still playing the 2013 TaylorMade TP MC irons, which we highlighted in our recent “Modern Classics: Old vs. New” video testing series.

FitzMagic teams back up

Brothers Matthew and Alex Fitzpatrick are teaming up once again at the Zurich this year, and Bettinardi Golf hooked them up with some festive “FitzMagic” headcovers to match this week.

See what else is in Alex Fitzpatrick’s WITB here

And, with that, we say goodbye to the Zurich Classic in New Orleans. Don’t forget to check out all of our photos from this week, including 30 unique photo galleries full of equipment photos.

We’ll see you next week in Texas for the 2024 CJ Cup Byron Nelson!

Your Reaction?