Club Building 101: How to properly turn down iron ferrules
Instruction
Clement: Why your practice swing never sucks
You hear that one all the time; I wish I could put my practice swing on the ball! We explain the huge importance of what to focus on to allow the ball to be perfectly in the way of your practice swing. Enjoy!
- LIKE0
- LEGIT0
- WOW0
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK2
Equipment
Mitsubishi Diamana WB: Club Junkie takes a technology deep dive
Earlier this week, Mitsubishi announced the return of its iconic Whiteboard profile with the new Diamana WB shaft.
In our launch story, we offered a rundown of the key technology in the new WB — 80-ton Dialead pitch fiber, Aerospace-grade MR70 carbon fiber, Consistent Feel Design, and the Xlink Tech Resin System. To go deeper, however, we enlisted our Resident Club Junkie and bona fide shaft nut, Brian Knudson, to track down someone from Mitsubishi at the PGA Show. Fortunately, Mitsubishi’s Director of Global Aftermarket Sales, Jonathan Alongi, was on hand to answer all of BK’s questions.
Check out their discussion about the new WB, as well as the 20th anniversary of the original design, in the video above — time stamps of key points below, including a definitive answer as to how the surfboard graphic ended up on the original Whiteboard in 2004!
- :40 – Mitsubishi Japan expands to the U.S. in 2004
- :50 – “The shaft that set the standard”
- 1:12 – “The ‘board is back”
- 1:45 – WB or Whiteboard? Or both?
- 1:55 – The first iteration of the sixth generation of Diamana
- 2:10 – Incorporating key technology from a 20-year journey
- 3:10 – Modifying the tip section for more ball speed
- 3:50 – Delivering ball speed in a low-launch, low-spin shaft
- 4:20 – Drilling down on the shaft profile compared to the original Whiteboard
- 5:00 – The most impressive element of the new WB
- 5:30 – Butt, mid, tip specifications
- 6:00 – WB’s iconic graphics and the Diamana legacy — flowers, surfboard, numbering system
- 8:15 – An abundance of available weights and flexes
- 8:55 – More players going lightweight
Check out more photos and see what GolfWRXers are saying about Mitsubishi WB in the forums.
- LIKE1
- LEGIT0
- WOW0
- LOL1
- IDHT1
- FLOP0
- OB0
- SHANK0
Equipment
2024 Vokey SM10 wedges: Club Junkie’s full fitting video
Our Resident Club Junkie, Brian Knudson, goes through a wedge fitting with Chris Baingo, Titleist’s Club Fitting Analyst.
Get the full story on new SM10 wedges in our launch piece.
- LIKE2
- LEGIT0
- WOW0
- LOL0
- IDHT0
- FLOP1
- OB0
- SHANK0
-
19th Hole2 weeks ago
Dave Portnoy places monstrous outright bet for the 2024 Masters
-
19th Hole3 weeks ago
Things got heated at the Houston Open between Tony Finau and Alejandro Tosti. Here’s why
-
19th Hole2 weeks ago
Tiger Woods arrives at 2024 Masters equipped with a putter that may surprise you
-
19th Hole3 weeks ago
Report: Tiger Woods has ‘eliminated sex’ in preparation for the 2024 Masters
-
19th Hole1 week ago
Two star names reportedly blanked Jon Rahm all week at the Masters
-
19th Hole6 days ago
Report: LIV Golf identifies latest star name they hope to sign to breakaway tour
-
19th Hole7 days ago
Neal Shipley presser ends in awkward fashion after reporter claims Tiger handed him note on 8th fairway
-
19th Hole5 days ago
Brandel Chamblee has ‘no doubt’ who started the McIlroy/LIV rumor and why
Jordan
Oct 3, 2019 at 11:12 am
How do you properly prepare a ferrule on finishes like black oxide, oil can, etc. I have been just prepping the ferrule to fit flush once installed. Is there an easier way of doing this?
The Club Nut
Oct 3, 2019 at 12:43 pm
Shouldn’t be a huge issue, but you can use a thin piece of masking or scotch tape below the ferrule to protect the oxide and finish from the belt if you’re really worried.
Ryan Barath
Oct 2, 2019 at 9:02 pm
HI WRXers, Thanks for watching
The belt in question is a standard 1X42″ durabrite belt from Golf Works. Its way easier on the ferrules than a linen one and does a way better job at slowly taking off material.
https://www.golfworks.com/durabrite-felt-ferrule-turning-belt/p/gw1065v/
Josh Hubin
Oct 2, 2019 at 8:24 pm
I think everything would love to know the specs on the belt. Thanks for the video Ryan.
Josh Hubin
Oct 2, 2019 at 8:25 pm
Everyone*
Steve Persing
Oct 2, 2019 at 7:42 pm
specifically what grit?
AC1284
Oct 2, 2019 at 4:28 pm
Ryan – what exact sanding belt do you use on your belt sander for this? Where do you purchase it? Thanks