Equipment
Want to trick out your putter? Here’s what you need to know
In 2019, one of the coolest parts of the golf world is the plethora of different ways you can accentuate your personality with cool golf swag. One of the most dynamic ways to do this is through a custom finished putter. I have spent the last six months (and about $1,000!) to make sure you get the best outcome for your money.
Intrigued? Good, here’s what you need to know…
Putter refinishing 101
- Stamping is done by hand and therefore never perfectly symmetrical
- Keep in mind there are certain things that cannot be fixed
- Have high expectations: with the right putter, these companies can transform your putter back to 9.99/10.
- Although each and every website has clear pictures, in my opinion the pictures are not perfect, particularly the black oxide/whisky/fuel finishes. It’s a little lighter than I expected and wears significantly more than black
- Sightlines can be a great addition to a putter, but remember, they cannot be removed!
The process
Over 25 years in golf has left me with a healthy collection of Scotty Cameron putters. When I was given an ultimatum to reduce my collection, I decided to take a unique approach: I would have several the old putters refinished. Armed with seven putters in approximately the same condition and the internet, I found seven different companies who offer a refinishing service. Each company cost between $125 and $129. I completed each of their questionnaires and sent them off, anxiously awaiting the results.
The results
One of the most important takeaways from this experiment is that NOT all refinishers are equal. In fact, the results were very binary: three of the companies did outstanding work, while four of the companies return a product which (in my opinion) was completely unacceptable.
Instead of “outing” the terrible work, I have decided to highlight the three companies which produced outstanding work: LabWorx (Waco, TX), Putter Lounge (Denver, Co) and NorCal Putters (Auburn, CA). Each of these companies returned work that was “nearly” new; removed dings, clean paint lines and held very closely to their estimate times.
Here is a Newport done by LabWorx (Waco) in their special “Armor” (more about this below). The finish is clean. All nicks and dents have been removed. It is basically new and looks amazing:
LabWorx “Armor”
LabWorx in Waco, TX deserves special note based on their R&D development of what they call “Armor”: a specially developed coating which does not impact feel but is extremely durable. The putter that I have, done in this coating has no glare and after almost eight months of play, shows no effects.
Not Just for Scotties
While I had only Scotty Camerons refinished, it is important that you understand that many different putters can be finished. According to Terri at Putter Lounge, “we have a lot of request for a number of different styles of putters, beyond Scotty Camerons, including a lot of Taylor Made Spiders.”
A total transformation that is completely custom for the very reasonable price of $129!
Getting your putter done
If you are looking to get your putter refinished, the first step is to have a clear idea of EXACTLY what you want. Next, I would recommend reaching out to a couple of companies (again, I highly recommend these three based on their work) and ask about wait times. Keep in mind that they can range from a couple of weeks to several months, with wait times increasing in the summer. After selecting the company, you want to go to their website and fill out the questionnaire about your putter; telling them exactly what you want. Send the putter, along with the form, and get ready to impress your friends!
Want to learn more?
LabWorx
NorCal Putters
Putter Lounge
- LIKE110
- LEGIT21
- WOW15
- LOL8
- IDHT4
- FLOP1
- OB3
- SHANK15
Equipment
Coolest thing for sale in the GolfWRX Classifieds (4/23/24): TaylorMade Qi10 Driver Ruby Red
At GolfWRX, we are a community of like-minded individuals that all experience and express our enjoyment of the game in many ways.
It’s that sense of community that drives day-to-day interactions in the forums on topics that range from best driver to what marker you use to mark your ball. It even allows us to share another thing we all love – buying and selling equipment.
Currently, in our GolfWRX buy/sell/trade (BST) forum, there is a listing for a TaylorMade Qi10 Driver Ruby Red.
From the seller: (@Gehly): “TaylorMade Qi10 Driver 9.0 Designer Series Ruby Red. Custom Mitsubishi Kai’li Red 60s (stiff) shaft, plays 46”. Great condition, head near mint (see pics). w/ Red/Black Golf Pride NDMC Midsize grip. No headcover for it. $545“
To check out the full listing in our BST forum, head through the link: TaylorMade Qi10 Driver Ruby Red
This is the most impressive current listing from the GolfWRX BST, and if you are curious about the rules to participate in the BST Forum you can check them out here: GolfWRX BST Rules
- LIKE0
- LEGIT1
- WOW1
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
Whats in the Bag
Sam Burns WITB 2024 (April)
- Sam Burns’ what’s in the bag accurate as of the RBC Heritage.
Driver: Callaway Paradym Triple Diamond S (9 degrees @10)
Shaft: Fujikura Ventus Blue 7 TX
3-wood: Callaway Paradym Ai Smoke Triple Diamond T (15 degrees @16)
Shaft: Fujikura Ventus Blue 8 X
Hybrid: Callaway Apex UW (21 degrees)
Shaft: Fujikura Ventus Blue 8 X
Irons: Callaway Apex TCB ’24 (4-AW)
Shafts: Project X 6.5 (4-PW), True Temper Dynamic Gold X100 Tour Issue (AW)
Wedges: Titleist Vokey Design SM10 (56-14F @55), WedgeWorks Proto (60-T)
Shafts: True Temper Dynamic Gold S400 Tour Issue (56, 60)
Putter: Odyssey Ai-One #7S
Grips: Golf Pride Tour Velvet Align
Ball: Callaway Chrome Tour X
Check out more in-hand photos of Sam Burns’ WITB in the forums.
- LIKE1
- LEGIT0
- WOW0
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
Whats in the Bag
Will Zalatoris WITB 2024 (April)
- Will Zalatoris’ what’s in the bag accurate as of the RBC Heritage.
Driver: Titleist TSR2 (9 degrees, A1 SureFit setting)
Shaft: Fujikura Ventus TR Black 7 X (44.5 inches)
3-wood: Titleist TSi2 (15 degrees, A1 SureFit setting)
Shaft: Fujikura Ventus TR Blue 8 X
Irons: Titleist T350 (3), Titleist T150 (4-PW)
Shafts: Nippon N.S. Pro Prototype G.O.S.T. 10 ST X (3), True Temper Dynamic Gold Tour Issue X100 (4-PW)
Wedges: Titleist Vokey Design SM10 (50-08F, 54-10S @55, 60-04T)
Shafts: True Temper Dynamic Gold Tour Issue X100
Putter: L.A.B. Golf Mezz.1 Max
Grips: Golf Pride Z-Grip Cord
See more photos of Will Zalatoris’ WITB in the forums.
- LIKE4
- LEGIT1
- WOW1
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
-
19th Hole2 weeks ago
Dave Portnoy places monstrous outright bet for the 2024 Masters
-
19th Hole2 weeks ago
Tiger Woods arrives at 2024 Masters equipped with a putter that may surprise you
-
19th Hole1 day ago
‘Absolutely crazy’ – Major champ lays into Patrick Cantlay over his decision on final hole of RBC Heritage
-
19th Hole3 weeks ago
Report: Tiger Woods has ‘eliminated sex’ in preparation for the 2024 Masters
-
19th Hole1 week ago
Two star names reportedly blanked Jon Rahm all week at the Masters
-
19th Hole1 week ago
Report: LIV Golf identifies latest star name they hope to sign to breakaway tour
-
19th Hole1 week ago
Neal Shipley presser ends in awkward fashion after reporter claims Tiger handed him note on 8th fairway
-
19th Hole6 days ago
Brandel Chamblee has ‘no doubt’ who started the McIlroy/LIV rumor and why
Robert
Sep 8, 2019 at 2:56 pm
Why would you not send a “Scotty” back to Scotty Cameron first? Is there a big price difference for the same request?
Fifteenclubs
Sep 8, 2019 at 11:08 pm
Cost for a Custom Shop refinish is about triple what the other companies charge and can take up to three months. I’ve sent putters back to Scotty as well as a couple of these guys and I’ll say if you send them a putter in decent shape it’ll come back looking like new. Same for Scotty but at a much higher price and longer lead time.
Robert
Sep 9, 2019 at 2:33 pm
Thanks for the reply.
Paul
Sep 7, 2019 at 10:01 pm
In my experience, most players that want to “trick out their putter” can barely break 90…
Ed
Sep 7, 2019 at 6:01 pm
Yet GolfWrx doesn’t realize many refinishers use one source – and call it their own. Just saying.
DB
Sep 8, 2019 at 12:57 pm
I have never heard this. You should provide more details.
2putttom
Sep 7, 2019 at 3:54 pm
wonderful
Vic Dirkes
Sep 7, 2019 at 3:06 pm
Putter Lounge bungled my Cameron. The head was not properly epoxied on and they did not follow my directions I carefully filled out. Was supposed to be murdered out and they left the insert the original color. The head was an easy fix but you spend $150 getting it done and it’s wrong. I will never use them again.
I know donkeys
Sep 7, 2019 at 2:06 pm
Matt Kuchar is a big donkey.
Erik Filipiak
Sep 8, 2019 at 9:21 am
You just offended ALL donkeys