Equipment
Aldila X-Torsion Black and Green Mamba shafts
Is the next new driver shaft craze on the way from Aldila?
Aldila’s new X-Torsion Black Mamba and X-Torsion Green Mamba shafts have a new design and use a “MAMBA” (Multi-Axial Material Bias Angle) material that’s designed for extremely low torque and spin — lower than any other shaft in the company’s stable, according to John Oldenburg, Vice President of Sales and Marketing at Aldila. And PGA Tour players are already taking notice.
At the 2016 RSM Classic, George McNeil and Charles Howell III used the Black Mamba shafts (designed for very low spin and launch), while Anirbahn Lahiri, Lucas Glover and Tad Ridings used Green Mambas (designed with a slightly softer tip, but still low spin and torque).
For many golfers with fast swing speeds, it’s beneficial to have a golf shaft that reduces twisting through impact, according to Oldenburg, because it allows the shaft to “recover” faster. Less torque and more torsional stability allows stronger golfers to “go at the ball” without worrying about the ball ballooning or spinning too much. Therefore, the goal, especially for Tour players with high swing speeds, is to design a shaft that has very high torsional stability. And Aldila’s new Mamba shafts have the highest torsional stability currently available from the company.
Both the X-Torsion Black Mamba and X-Torsion Green Mamba shafts use what Aldila calls a “flat-weave” construction in its tip section (the bottom part of the shaft), which is where the majority of shaft twisting occurs during a golf swing. The construction method weaves together individual fibers that are positioned in opposing 45-degree angles in an over-under structure that creates a thin, strong and highly consistent woven graphite fabric.
Aldila says its woven technology is superior because it’s used on both the interior and exterior of the shaft, which enhances stability. Most weaves are placed on the interior of the shaft to protect the weaves from abrasion, but Aldila’s unique “lay-up and sanding process” protect the integrity of its flat weave, allowing it to be used on the outside of the shaft as well.
The flat-weave construction is also novel because of it spreads and flattens the graphite fibers used to create the shaft, allowing them to be thinner and thus improving the precision of the weave. Those graphite fibers are also are stronger than typical graphite weave materials. They use intermediate modulus materials that measure 44 MSI, according to Aldila, 33 percent stiffer than 33 MSI fibers typically used. That further enhances stability.
So how does Aldila show off all that technology in a shaft named Mamba? A snake-skin-esque exterior, of course. See what GolfWRX members are saying about the shafts in our forums.
- LIKE106
- LEGIT21
- WOW9
- LOL4
- IDHT5
- FLOP3
- OB2
- SHANK18
Equipment
Why Rory McIlroy will likely use the new TaylorMade BRNR Mini Driver Copper at the RBC Heritage
Although we spotted Rory McIlroy testing the new TaylorMade BRNR Mini Driver Copper last week during practice rounds at the Masters, he ultimately didn’t decide to use the club in competition.
It seems that will change this week at the 2024 RBC Heritage, played at the short-and-tight Harbour Town Golf Links in Hilton Head.
When asked on Wednesday following his morning Pro-Am if he’d be using the new, nostalgic BRNR Copper this week, McIlroy said, “I think so.”
“I like it,” McIlroy told GolfWRX.com on Tuesday regarding the BRNR. “This would be a good week for it.”
View this post on Instagram
According to Adrian Rietveld, the Senior Manager of Tour at TaylorMade, the BRNR Mini Driver can help McIlroy position himself properly off the tee at the tight layout.
Here’s what Rietveld told GolfWRX.com on Wednesday:
“For someone like Rory, who’s that long at the top end of the bag, and then you put him on a course like Harbour Town, it’s tough off the tee. It’s tight into the greens, and you have to put yourself in position off the tee to have a shot into the green. It kind of reminds me of Valderrama in Spain, where you can be in the fairway and have no shot into the green.
“I’m caddying for Tommy [Fleetwood] this week, so I was walking the course last night and looking at a few things. There’s just such a small margin for error. You can be standing in the fairway at 300 yards and have a shot, but at 320 you don’t. So if you don’t hit a perfect shot, you could be stuck behind a tree. And then if you’re back at 280, it might be a really tough shot into the small greens.
“So for Rory [with the BRNR], it’s a nice course-specific golf club for him. He’s got both shots with it; he can move it right-to-left or left-to-right. And the main thing about this club has been the accuracy and the dispersion with it. I mean, it’s been amazing for Tommy.
“This was the first event Tommy used a BRNR last year, and I remember talking to him about it, and he said he couldn’t wait to play it at Augusta next year. And he just never took it out of the bag because he’s so comfortable with it, and hitting it off the deck.
“So you look at Rory, and you want to have the tools working to your advantage out here, and the driver could hand-cuff him a bit with all of the shots you’d have to manufacture.”
So, although McIlroy might not be making a permanent switch into the new TaylorMade BRNR Mini Driver Copper, he’s likely to switch into it this week.
His version is lofted at 13.5 degrees, and equipped with a Fujikura Ventus Black 7X shaft.
See more photos of Rory testing the BRNR Mini here
- LIKE5
- LEGIT0
- WOW0
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
Equipment
Spotted: TaylorMade P-UDI driving iron
It seems like the RBC Heritage is full of new gear to be spotted, and you can add TaylorMade’s P-UDI utility irons to that list.
We spotted a 17-degree P-UDI 2-iron in Nick Dunlap’s bag yesterday, and now have some photos of both the 3- and 4-irons. Nick has his P-UDI 2-iron setup with a Project X HZRDUS Black 4th Gen 105g TX shaft.
From what we can tell, this new P-UDI utility iron looks to have some of the usual TaylorMade technology as we can see the Speed Slot on the sole of the club for additional face flexibility. A toe screw is usually used to close off the hollow body design that will probably be filled with a version of TaylorMade’s Speed Foam that is present in the current iron lineup. This hollow body, foam-filled design should offer additional ball speed, soft feel, and sound, as well as an optimized CG for ball flight.
“Forged” is etched into the hosel, so we can assume that either the face, body, or both are forged for a soft and responsive feel. The club looks good from behind and at address, where we can see just a little offset and a topline that I would consider medium thickness. We don’t have the full details on what is under the hood or how many loft options will be available yet.
TaylorMade P-UDI 3-iron – 20°
TaylorMade P-UDI 4-iron – 22°
- Check out the rest of our photos from the 2024 RBC Heritage
- LIKE5
- LEGIT1
- WOW1
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
Whats in the Bag
Collin Morikawa WITB 2024 (April)
- Collin Morikawa what’s in the bag accurate as of the RBC Heritage. More photos from the event here.
Driver: TaylorMade Qi10 LS (9 degrees)
Shaft: Mitsubishi Diamana D+ Limited 60 TX (45 inches)
3-wood: TaylorMade Qi10 (13.5 degrees)
Shaft: Mitsubishi Diamana D+ Limited 80 TX
5-wood: TaylorMade Qi10 (18 degrees)
Shaft: Mitsubishi Diamana D+ Limited 80 TX
Irons: TaylorMade P770 (4), P7MC (5-6), P730 (7-PW)
Shafts: True Temper Dynamic Gold Tour Issue Mid 115 X100 (4-6), True Temper Dynamic Gold Tour Issue X100 (7-PW)
Wedges: TaylorMade MG4 (50-SB09, 56-LB08), TaylorMade MG4 TW (60-TW11)
Shafts: True Temper Dynamic Gold Tour Issue S400
Putter: TaylorMade TP Soto
Grip: SuperStroke Zenergy Tour 2.0
Grips: Golf Pride Z-Grip Cord
Ball: TaylorMade TP5x
- LIKE1
- LEGIT0
- WOW1
- LOL0
- IDHT0
- FLOP0
- OB0
- SHANK0
-
19th Hole1 week ago
Dave Portnoy places monstrous outright bet for the 2024 Masters
-
19th Hole2 weeks ago
Things got heated at the Houston Open between Tony Finau and Alejandro Tosti. Here’s why
-
19th Hole1 week ago
Tiger Woods arrives at 2024 Masters equipped with a putter that may surprise you
-
19th Hole2 weeks ago
Report: Tiger Woods has ‘eliminated sex’ in preparation for the 2024 Masters
-
19th Hole3 days ago
Two star names reportedly blanked Jon Rahm all week at the Masters
-
19th Hole2 days ago
Neal Shipley presser ends in awkward fashion after reporter claims Tiger handed him note on 8th fairway
-
19th Hole2 weeks ago
Addiction, spinal fusion, and scam artists – Everything Anthony Kim revealed in candid interview with David Feherty
-
19th Hole2 weeks ago
Anthony Kim says doctors told him that he ‘may not have much time left’ ahead of LIV return
Matt K
Dec 15, 2016 at 1:58 pm
Is this the Rogue M-ax rebranded? A lot of the commenters hated the graphics and name for the M-AX. This is undoubtedly better, wonder if the profile/material is the same though.
Mat
Dec 13, 2016 at 5:18 am
X-torsion. Most accurately named shaft in the history of golf equipment. 🙂
Dave R
Dec 12, 2016 at 1:53 pm
One guy peed, someone’s noodle is to soft and so is his butt and he hopeing for a stiff shaft. What type of forem are we on here? The Anti guy is right get some rebar and go play.
Rd
Dec 13, 2016 at 3:16 am
And you’re so excited, you can’t type nor spell
KK
Dec 11, 2016 at 8:23 pm
I peed a little just looking at the pics
Snope
Dec 11, 2016 at 3:11 pm
Just make them feel as solid as the RIP Alpha and Beta, I’ll take 10 each
Teaj
Dec 11, 2016 at 2:12 pm
I wonder if this is going to transition into an iron and hybrid/driving iron shaft line? Has anyone seen the specs for these bad boys? or even just weights?
Matt
Dec 11, 2016 at 12:18 pm
Again I hope that the shaft isn’t soft in the mid section or the butt. There are a lot of low spin shafts that feel like noodles
LaBraeGolfer
Dec 11, 2016 at 12:57 pm
Unfortunately, a shaft has to have a soft point in the bend profile.
The Anti-Smiz
Dec 11, 2016 at 1:33 pm
you guys should just go swing some literal re-bar with your super-fast-in-an-internet-forum swing speeds.
Port
Dec 11, 2016 at 2:27 pm
Love it!
Matt
Dec 12, 2016 at 6:54 pm
Soft is a relative term. I find the Tour AD to be soft, the non-TS Fuji Motore, the 70g version of the White/Blue felt soft to me. I prefer the V2, Protopype, F7M2 Ltd, etc.