First let me say a couple things..first it took me a bit longer to get a Fair bit of play on FIRM ground…as its been far to soggy in the PNW lately…but I traveled over to the eastern part of the state where the ground is firm to duplicate more realistic playing conditions than the mush around Portland/Seattle!
Let me preface what I have been playing prior to the C-TAPERS, I play to single digit handicap, iron play for the most part has been one of the stronger parts of my game. When playing well I like to take a small divot…I have been playing PX 6.5’s for a while now and PX 6.0 prior to that for the past several years…with a couple runs of DG x100’s just to keep things interesting. I have also spent a great deal of time and money trying pretty much every brand and style of iron shafts that come around…but alway have come back to my steady eddies PX’s due to the reduced spin, flight and consistence distances. In fact my good buddies Swanry30, desallie and I did a Trackman shoot out between PX and DG recently and pretty much confirmed what I had seen in the real world for quite some time…DG just spin too much for me and where the PX don’t and hence I’m about 1 club longer with them (individual results will vary) but those are mine.
Second, the C-TAPERS are like No other shaft I’ve ever tested…and in all honesty it took me a while to get accustomed to the differences-in fact the first 5-6 times I initially hit the c-tapers I was quite perplexed as to what I was experiencing due the sound and feel even thou the results were always there and I wasn’t confidant in what I was going to write about and tell of my experience until first I got out of the SOGGY pit of the NW and hit some firm ground.
I don’t have any Trackman numbers yet (hopefully soon) so most of what I’m relating is by good ole ballflight and distance.. I hit my Satin PX 6.5 side by side the C-Tapers as the comparison.
Feel: The C-Tapers are very quiet in the feel department…meaning they are soo smooth that I really wasn’t sure I was loading the shaft this was quite a contast to the PX which has quite a ‘pop’ to them and the DG’s which you really feel the action of the shaft all the way thru the shaft. While the C-tapers are, what I would call as ‘Refined’ as it gets…the load seems to be transfers through out the shaft almost without notice…which initially I found this alarming but soon understood what was happening as the results were there.
Sound: Again I’ll use the word ‘Quiet’, as in contrast to my PX the sound of impact is very muted, soft, yet firm but certainly many decibels lower. Again I found this puzzling combine with the feel- once I became accustomed to it very pleasing.
Ballflight: This is where rubber meets the road, I would agree with KBS statement about 5% lower than the competition. I found specifically the mid and long irons (6i-3i) to flight lower than the PX’s. And the short irons a bit closer to the PX flight.
Workability: The C-Tapers are definitely more workable(or rather feel more) than PX, but DG still is the king on the feel dept. when it comes to working the ball but not necessary the results. I found the actual workable part of the C-tapers could come close to hanging with DG’s even thou they didn’t necessary feel like they were..make sense? But I would say they are a great bridge between PX and DG in this category.
I had a shot on a par 4(hit my 3w off the tee left on a dogleg right into the trees)…was sitting about 165yards out uphill to the green surrounded by Pine trees…but had a small window to needle thru 3 trees in front of me but had to keep the shot low …So I have to hit a low hook just to get to the fairway(which was all I was trying to do)..So I set with a 5i and the shot came out perfect and actually went about 2 ft past the green…(for those of you keeping score).I missed the putt for par!
Distance: The I would also say KBS statement is likely true again with the 5% gain in distance, this was more evident in the mid and long irons to me..I will also throw this into the distance segment…I choose the S+ set of C-tapers, imo they feel very close to flex of my PX 6.5’s Satins, however I think the X flex’s would be a better comparison in straight terms of the px.6.5 for distance, as the added spin which allows the the shafts to Be Workable also spins just a bit more and coupled with a 1/2 flex under what I should be playing makes them play just a tad shorter than what I have be accustomed to…I look forward to picking up a set of X flex’s in the very near future as KBS C-tapers have all the things I have been looking for in irons shafts.
Final thoughts: I really believe KBS has a winner with the C-Tapers, this is by far the best KBS shaft I have tried- they look awesome, the abilities to feel and work the ball is great, the ball flight is consistent and distance is good but I have since determined that the S+ are slightly too soft for my iron game, but loo forward to giving them a go again when I get the correct flex. And after all of that I really think KBS has great product here, perhaps even the best of them all-
Inspired from tour player feedback, the KBS C-TAPER shaft is specially designed to produce a lower flight and spin rate while delivering the signature benefits of a piercing trajectory and smooth feel. By stiffening the shaft profile in the lower taper rate and early tip section, the C-TAPER is engineered to maximize shot performance for players that currently have too high a trajectory.
Incorporating signature AST technology, the C-TAPER shaft produces a smooth feel through contact while maximizing energy transfer for distance gains and better control of the ball.
MRC Shaft Shootout: Tensei CK Pro White, Kuro Kage XT and Diamana BF-Series
The Tensei CK Pro White is the latest release from Mitsubishi Rayon Composites (MRC), a low-launch, low-spin shaft with a multi-material design that the company says improves the performance and feel of the shaft. Whereas most golf shafts use between 3-6 different materials in their construction, the Tensei CK Pro White is made from 11 different materials, giving MRC engineers greater precision in the shaft’s design.
Like MRC’s Tensei CK Pro Blue shafts, which produce a slightly higher-launching, higher-spinning ball flight, the CK Pro White uses MRC’s Carbon Fiber DuPont Kevlar Weave in the handle section of the shaft. The company says it increases the strength and stability of that part of the shaft, leading to better feedback.
On the other end of the shaft, the tip section, MRC uses a boron-reinforced fiber. All low-launch, low-spin shafts have stiff-tip designs, but the addition of boron puts the Tensei CK Pro White in a class of its own when it comes to lowering launch angle and spin rate. The boron fiber also reduces torque, which can offer better energy transfer, more accuracy and better feedback — especially for skilled, high-swing-speed golfers.
Connecting and reinforcing those areas of the shafts is MRC’s low-resin content (LRC) prepreg. Prepreg is carbon fiber that’s been reinforced or “pre-impregnated” with resin, a glue that holds the material together when it’s formed into sheets and rolled into the form of a shaft. MRC says that its LRC has 15 percent more carbon fiber and 13 percent less resin than traditional prepregs, which allows MRC to make the Tensei CK Pro White stronger without adding extra weight to the shaft. MRC also uses high-modulus, 40-ton prepreg in the Tensei CK Pro White’s design, which like LRC is thinner, stronger and lighter than traditional prepregs.
In the EI chart below, you can see how the Tensei CK Pro White’s bend profile compares to the CK Pro Blue. The main differences are its slightly stiffer tip and mid sections, as well as its slightly softer butt section. That gives the CK Pro White a higher “kick point” than the CK Pro Blue. Generally, the higher the kick point of a shaft, the lower its launch conditions. That’s why the Tensei CK Pro White is a lower-launching, lower-spinning shaft than the Tensei CK Pro Blue.
Just how much lower launching and lower spinning is the Tensei CK Pro White than MRC’s latest premium driver shafts? I put it to the test against the company’s Kuro Kage XT and Diamana BF-Series, which like the CK Pro White are PGA Tour-quality shafts that sell for about $400 each. All three shafts tested were built to my spec: 70TX, tipped 1 inch at a finished length of 45.5 inches.
I tested the three shafts on Trackman 4 at the Launch Pad at Carl’s Golfland in Bloomfield Hills, Mich. After warming up, I hit 10 drives with each shaft, and whittled my shots down to the most similar five to help illustrate the differences. Premium balls were used for the test, and results were normalized.
As expected, the Tensei CK Pro White was the lowest-launching, lowest-spinning shaft in the test. That’s impressive in its own right, but what will really excite golfers when they try a Tensei CK Pro White is the shaft’s feel. It’s noticeably smoother than the MRC White Board shafts I’ve played in the past. You could likely duplicate the launch conditions of the Tensei CK Pro White with similar products from other premium shaft makers, but I’m not sure its smoothness can be replicated in the category. It’s something special, and I expect a lot of serious golfers with above average club head speeds will be willing to pay a premium for it.
MRC’s Kuro Kage XT uses a stouter iteration of the company’s famed “Blue Board” bend profile, and in that regard it’s quite similar to the Diamana BF-Series. That’s what makes the shafts a little higher launching and higher spinning than the Tensei CK Pro White. The Kuro Kage XT has a much different feel than both, however, due to its use of an elastic wire made of Titanium and Nickel that MRC calls “TiNi” wire.
Related: Learn more about the Kuro Kage XT
In the Kuro Kage XT, the TiNi wire is added to the bottom 13 inches of the shaft, where it adds stability, but it also serves another purpose. Its elasticity allows the bottom end of the shaft to better load and unload during the downswing to help improve energy transfer. That’s what gives the Kuro Kage XT its more active feel, at least compared to the boron-infused tip section of the Tensei CK Pro White, which by design offer no elasticity.
The Diamana BF-Series also uses boron in its tip section, and its combined with a new, aerospace-grade fiber called MR-70 to create what MRC says is a first-of-its-kind hybrid prepreg. MR-70, which is manufactured by parent company Mitsubishi Chemical, is 20 percent stronger and has 10 percent more modulus than similar fibers, MRC says. The handle section of the BF-Series is reinforced with MRC’s Pitch Fiber, which functions to boost energy transfer like the CK Pro White’s Carbon Fiber DuPont Kevlar Weave.
In terms of launch conditions, the best fit for me was the Diamana BF-Series. It launched the ball a little higher than the Tensei CK Pro White, and added a little spin to help keep my drives in the air. It was also easier to swing than the Tensei CK Pro White, helping me more easily hit a draw while offering an even smoother feel due to its less rigid tip and mid sections.
To recap, if you need to lower your launch conditions, the Tensei CK Pro White is one of the most intriguing new MRC options to help you do so. Need a higher ball flight? Try the Diamana BF-Series. And if you want a radically different feel, give the Kuro Kage XT a try.
Have a question? Let me know in the comments section below and I’ll do my best to answer as many as I can.
Weights and Flexes
- Tensei CK Pro White: 60 (R, S, TX), 70 (S, TX), 80 (TX)
- Kuro Kage XT: 50 (R, S, X, TX), 60 (R, S, X, TX), 70 (S, X, TX), 80 (S, X, TX)
- Diamana BF-Series: 50 (R, S, X), 60 (R, S, X, TX), 70 (S, X, TX), 80 (S, X, TX)
Review: KBS Tour FLT Shafts
Pros: FLT shafts use a flighted design, which helps golfers launch their long irons higher and with more spin. The FLT short-iron shafts provide a more penetrating trajectory for more control.
Cons: FLT shaft flexes correspond with weight, so golfers may not be able to match their desired shaft weight with their desired flex.
Who They’re For: Golfers who need more spin or more launch from their long irons to optimize their trajectory. Everyone from beginners to PGA Tour players can use the shafts effectively, but they’ll be most popular with golfers with moderate-to-slow swing speeds, or any golfer who generates low-spin launch conditions.
Selecting the proper iron shafts is one of the most important equipment decisions golfers make. It’s an issue of quantity. Most golfers carry about 7-8 irons in their bag, so if they choose the wrong iron shaft, they’ve made the game harder than it needs to be with half or more of their clubs.
The good news is that there’s a wider selection of quality iron shafts than there has ever been, with recent growth in models that are designed to help golfers hit their iron shots higher and farther, while still maintaining PGA Tour-quality consistency and feel.
KBS is one of the leading steel shaft manufacturers, and already offered a wide variety of models prior to its newest shaft launch. Company representatives felt KBS was lacking a product for a particular segment of golfers, however, so it developed its new FLT shafts.
FLT shafts ($31.95 each) have a flighted design, which helps certain golfers optimize the performance of each iron their bag. The long irons shafts have progressively softer tip sections, which helps golfers increase their launch angle and spin rates with those clubs. For the right golfer, the design will help them hit their iron shots farther, and stop shots on the green more quickly. In the short irons, where height and spin are easier for golfers to generate, the FLT shafts are stiffer, which creates the flatter trajectory most golfers prefer with their scoring clubs. The crossover point between the higher-launching long irons and lower-launching short irons is the 7 iron.
Like all KBS shafts, FLT models have a constant weight, which means that long iron shafts and short iron shafts will be roughly the same weight through the set. Shaft weight is dependent on flex, however, as softer-flex models are lighter than stiffer-flex models. So if you’re looking for a really heavy, regular-flex shaft or a really light, extra-stiff-flex shaft, these aren’t for you.
Keep in mind that KBS shafts do not have reinforced tip sections like many other iron shafts, which gives them a slightly higher balance point and can decrease swing weight by 1-2 points. I personally like the feel of KBS shafts and their slightly higher balance point, but some golfers won’t.
For this review, I tested the new FLT shafts head to head against KBS Tour shafts of the same flex and weight (130X) in 4 irons, 6 irons and pitching wedges. Each of the shafts were installed in Callaway’s Apex Pro ’16 irons, and were built to my specifications (standard grips, standard length, 1-degree strong lofts, 1-degree flat lie angles).
I performed my testing at the Launch Pad at Carl’s Golfland in Bloomfield Hills, Mich., where I hit the 4 irons, 6 irons and pitching wedges on Trackman IV with premium golf balls. I hit 3-6 solid shots with each iron, and then removed the outliers from the final data in an attempt to compare only the most similar strikes. Results were normalized.
As you can see from the data, there was a significant difference in the flight of the 4 irons with the two different shafts, but less of a difference with the 6 irons and pitching wedges.
As expected, the FLT shafts caused 4 iron shots to launch higher (0.8 degrees) and with more spin (729 rpm) than the KBS Tour shafts. I’m not a low-spin player, which is one of the target audiences for this shaft, so the added launch and spin of the FLT shafts caused my 4 iron shots to fly shorter. Golfers who launch their irons too low or with too little spin, however, will likely see a distance increase when using the FLT shafts.
As I moved closer to the short end of the set, the two shafts started to perform more similarly. Theoretically, the 6 iron shots with the FLT shafts should have launched slightly higher and spun more than 6 iron shots with the KBS Tour shafts, but I actually saw a slightly lower launch angle (0.5 degrees) with the FLT. The spin was higher, though, by 211 rpm. With the pitching wedges, the results were again quite similar. The FLT launched 0.9 degrees higher, but actually spun 271 rpm less than the KBS Tour shafts.
Stepping back from the numbers, I was impressed with how similar the feel was between the KBS Tour and FLT shafts. Yes, I could feel that the FLT shafts were more active in the tip with the 4 irons, but they felt nearly the same in the 6 irons. By the time I got to the pitching wedges, the two shafts were indistinguishable. The KBS Tour is considered one of the better-feeling iron shafts currently available, so KBS’ ability to replicate that feel in the FLT will be a plus for the majority of interested golfers.
Looking more broadly, trends in shaft design tends to go hand-in-hand with trends in club head design, and the FLT shafts are no exception. Equipment manufacturers continue to strengthen the lofts of their distance irons; they have to in order balance the launch equation, as their faster ball speeds create a higher launch angle and more spin.
While the improvements to iron design have allowed golfers to hit their mid and short irons farther, many golfers continue to struggle to hit their long irons high enough or consistently enough for them to be effective. And based on my testing results, it’s clear that the FLT shafts can make long irons more playable for certain golfers, and maybe even keep long irons in a golfer’s bag that might otherwise be kicked out for higher-flying hybrids or fairway woods.
As always, I recommend that golfers get properly fit for iron shafts, which means visiting a reputable club fitter in your area. So if you’re in the market for new irons or iron shafts, you can get started by going through KBS’ Online Fit System, which upon completion lists KBS-certified dealers in your area.
Review: Paderson Driver Shafts
Pros: Four distinct driver shaft profiles are available in a wide range of flexes. Paderson’s filament-wound construction (used in three profiles) offers a unique feel. By premium shaft standards, these are a bargain at $199 each.
Cons: Limited weight options.
Who They’re For: Anyone can play a Paderson shaft.
Buying a golf shaft is like buying a new pair of running shoes. If the shoes don’t fit your foot, it doesn’t matter how good their technology is. You’re going to run slower, and you’re not going to be as comfortable as you could be.
A golf shaft is the same way. If it doesn’t fit your swing, you’re not going to hit shots as far or straight as you could. A mismatched shaft won’t give you blisters like mismatched shoes, but it will wear on your confidence. For golfers, that’s arguably even more painful. So the challenge for premium shaft makers like Paderson, which is targeting both professional and average golfers, is two-fold. The company has to create several types of shafts in an effort to fit as many golfers as possible, but also include technology that has its shafts stand apart from its competition.
While not a household name now, Paderson has the traits of a shaft company that could be. That’s thanks to its filament-wound manufacturing technique, which is used in three out of the four driver shafts the company produces. It’s unique to the industry, and also used in the company’s fairway wood, hybrid/utility and iron shafts. To learn more about Paderson’s claims and technologies, you can read this in-depth Q&A we did with company CEO Jason Horodezky. For the purposes of this review, however, I’ll do my best to explain the company’s technologies as simply as possible.
Most graphite shafts are made from several sheets of carbon fiber and resin, a glue that holds the fibers together. To create a shaft, these sheets, called “pre-preg,” are wrapped tightly around a steel rod called a “mandrel,” which sets a shaft’s geometry. Different types of pre-preg have different characteristics, and sometimes exotic materials are used to change those characteristics, which generally drive up the cost. It’s the thickness, stiffness, torsional qualities and orientation of the materials used that determine the weight, stiffness and bend profile of each shaft. Once the wrapping process is complete, the shafts are put in a special oven, where the sheets are laminated, or melded together, to create a graphite tube. The shafts are then sanded smooth and painted, creating the finished product.
Paderson’s shafts are formed on a mandrel, too, but the filament-wound process used for three of the driver shafts tested (KG860, KG860TP and the upper part of KG972) is much different. They are, in essence, “braided” from two continuous strands of carbon fiber and kevlar, which the company says allows its shaft to not only be more consistent, but create superior energy transfer when compared to other shafts. Paderson says it can actually “pre-load” tension in its shafts, harnessing the energy of the vibrations created during the swing to increase ball speed.
According to the company, one of its four driver shaft models will work for any golfer, as they’re available in a variety of flexes ranging from Ladies to XX-Stiff. Unlike many shafts on the market, however, golfers can’t pick the weight and flex of Paderson shafts independently. Each flex is constructed with a specific weight the company says optimizes ball flight, so weight options depend on shaft model and flex.
Bolstering Paderson’s consistency claims is that the filament-wound process does not require its shafts to be sanded, so the texture seen on its shafts is not cosmetic, but rather the actual appearance of a shaft’s fibers, sealed with a layer of clear-coat.
Paderson also makes shafts that aren’t fully filament-wound, and claims its lamination technique is superior to typical processes. Its KG972 shaft, for example, uses a filament-wound upper portion and a laminated lower portion. The company’s Amorphous shaft, on the other hand, is 100 percent laminated. What’s different about Paderson’s lamination process, according to the company, is that it uses vacuum-curing, a temperature-controlled process that pulls resin through the shaft to minimize resin content, which allows for more fine-tuned designs.
Intrigued? So was I, so I put Paderson’s shafts to the test.
The Testing Data
I sent my launch monitor and swing profile information to Paderson, which in turn sent me four of its latest shaft models to test. My results are above, but I feel that the numbers don’t tell the whole story. For that reason, I’ve included an individual write up about each shaft below.
Testing Procedure: I took the four Paderson shafts, as well as my gamer shaft I was fit for in the fall of 2015, to Carl’s Golfland in Bloomfield Hills, Mich. I tested all five shafts at its Launch Pad custom-fitting facility on Trackman. I used a TaylorMade M2 driver (9.5 degrees, set to neutral) and each of the shafts tested measured 45.5 inches.
KINETIXX Kevlar Green 860TP
Right now, the graphite shaft market is trending toward the tip-stiff, low-torque designs shafts that are regularly finding the winner’s circle on the PGA Tour. If those shafts have worked successfully for you, then the 860TP could be the Paderson shaft that fits you best. It is the lowest in torque of any Paderson driver shaft, and has also has the stiffest tip section. That makes it a good fit for golfers with an aggressive transition, or those who tend to hook the ball.
I tested all the Paderson shafts in a D40 flex, which equates to an X-flex, and more than the others, the 860TP felt very stout and stable. I was impressed with how smooth and balanced it felt for a high bend-point shaft, though.
With the 860TP, I had the highest average swing speed, which gave it the greatest potential for maximum distance. I struggled to find the center of the face, however, which is why I didn’t generate as much ball speed with it. The shaft did create the highest launch angle, and like all the Paderson shafts, it outperformed my gamer, a low-torque, tip-stiff 70X shaft that was most similar to the 860TP.
KINETIXX Kevlar Green 860
The Kevlar Green 860 is Paderson’s “baseline” shaft. It fits the widest segment of the golfing population as a whole, and suited my swing better than the 860TP due to its slightly softer tip section and higher torque. I liked the way it felt, and as you can see in the dispersion graphic above, I hit it the most consistently.
My angle of attack was also the most up, or positive, with the 860, which helped me create the longest total distances with the shaft. If I was playing in a tournament tomorrow, this is the shaft I would play.
KINETIXX Kevlar Green 972
To me, the the KG972 is Paderson’s most interesting shaft, with a filament-wound upper half and a laminated lower half. The multi-construction approach gives the shaft a slightly higher balance point than Paderson’s other driver shafts, or “counterbalancing” effect. It tends to fit golfers with a smooth transition, according to the company, and felt extremely easy to swing in testing.
While the 972 created the fastest ball speeds and longest carry distance, its comparatively softer-tip design didn’t suit my swing. I felt a lot of “kick” at the bottom, and I felt as though it had more draw bias than the others.
KINETIXX VMT Vacuum Cured KVMT870
The 870 has gained traction in the long-drive community. It’s a fully laminated shaft, and does not use the company’s filament-wound technology.
The 870 has a dual kickpoint, according to Paderson, which causes the shaft to bend low in the butt and high in the tip to improve energy transfers for certain players. At 66 grams, it was also 5-10 grams lighter than the other Paderson shafts I tested. The 870 felt more active than all but the 972, however, and I preferred the heavier weight and more stable feel of the 860 and 860TP shafts.
At $199 each, Paderson’s shafts are more affordable than most premium shafts, and my testing showed that one of the company’s shafts has the potential to meet, or in my case exceed the performance of your current shaft. If one of Paderson’s shafts suits your swing, and one likely will, it deserves serious consideration — even among shafts that cost hundreds more.
Gary Woodland’s winning WITB: 2019 U.S. Open
Tiger Woods WITB: 2019 U.S. Open
Forum Thread of the Day: “Most overrated/underrated equipment in golf”
Patrick Cantlay’s winning WITB: 2019 Memorial Tournament
One post, many questions: New Mizuno irons on the way?
Forum Thread of the Day: “If you are a 10 handicap with declining length, what clubs do you buy?”
Rory McIlroy’s winning WITB: 2019 RBC Canadian Open
WRX Spotted: Titleist 620 CB, MB and T100 irons
Chez Reavie’s winning WITB: 2019 Travelers Championship
WRX Spotted: Ping Glide 3.0, Glide 3.0 Eye2 wedges
The 2019 Open Championship tee times; Tiger Woods grouped with Patrick Reed and Matt Wallace
The 2019 Open Championship tee times have been released for Round One, and it’s the 2011 champion Darren Clarke who...
The 6 best #GolfWRX photos on Instagram today (7.15.19)
In this segment, we’ll be taking a look at some of the best #GolfWRX tagged photos on Instagram. In case...
Puma launches new X Collection that Rickie Fowler will debut at this week’s Open Championship
Puma Golf has launched its new X Collection which is inspired in part by the celebration of Rickie Fowler’s 10-year...
2019 Open Championship odds
Rory McIlroy enters the 148th Open Championship as the betting favorite at 8/1 as he looks to win the claret...
Equipment2 weeks ago
Forum Thread of the Day: “Most overrated/underrated equipment in golf”
Equipment2 weeks ago
One post, many questions: New Mizuno irons on the way?
Equipment3 weeks ago
WRX Spotted: Ping Glide 3.0, Glide 3.0 Eye2 wedges
Whats in the Bag1 week ago
Matthew Wolff’s winning WITB: 2019 3M Open
Opinion & Analysis2 days ago
Why do Tour players prefer fades over draws from the tee box?
Whats in the Bag2 weeks ago
Nate Lashley’s winning WITB: 2019 Rocket Mortgage Classic
Equipment3 weeks ago
Forum Thread of the Day: “European Tour looking into an incident involving Matt Wallace and his caddie from the BMW International Open”
News1 week ago
Teryllium is back: Scotty Cameron T22 putters launch