Connect with us

Equipment

Callaway X2 Hot and X2 Hot Pro Irons

Published

on

The most important new feature of Callaway’s new X2 Hot and X2 Hot Pro irons is something that on first glance, golfers might not even notice: Chevron-shaped silver arches on the back of their cavities.

While they look like part of the badging, the arches are actually cast into the faces of the 17-4 stainless-steel irons and play a key role in stabilizing the upper portion of their face. That improves the sound and feel of the irons, and makes them more consistent.

X2 Hot irons

callaway x2 hot

Photo above: Callaway’s new X2 Hot iron are 40 percent more consistent than the X Hot irons. 

The X2 Hot irons don’t have the high-strength 455 carpenter stainless-steel faces of Callaway’s Apex irons, but their stabilizing arches allow the lower portion of their faces to flex more at impact. That moves their sweet spots lower, where most golfers contact their iron shots. It also helps shots hit below the sweet spot retain more ball speed and launch angle, a big part of the X2 Hot’s 40 percent improvement in consistency.

callaway x2 hot iron

Photo above: The X2 Hot irons have a deeper undercut behind the face, which helps make them about 2.5 yards longer than the X Hot irons.

The position of the mass in the X2 Hot iron heads was also changed to make them look less overtly like game-improvement irons. While the blade lengths, top lines and amount of offset remain very similar, the irons were slimmed substantially from front to back.

X2 Hot, X Hot comp

Designers were careful to keep the X2 Hot irons as forgiving as last year’s model, and at the same time move the center of gravity slightly lower and more forward. That, along with the deeper undercuts behind the faces of the irons, helps make them about 2.5 yards longer than their predecessors. The sole widths are also about the same size as they were on the X Hot irons, but 2-to-4-degrees more bounce was added to help golfers improve their turf interaction.

callaway x2

Photo above: A Callaway X2 Hot iron, viewed from address. Its toplines are thicker than those on Callaway’s X2 Hot Pro irons. 

Like Callaway’s Apex irons, the X2 Hot irons have Callaway’s 30-degree wide-spaced V grooves. They will be available Jan. 17 and cost $799 with True Temper’s Speed Step 85 steel shaft (regular and stiff flexes), $899 with Callaway’s X2 Hot 60-gram graphite shaft in lite, regular and stiff flexes.

Screen Shot 2013-11-11 at 10.42.56 AM

X2 Hot Pro irons

callaway x2 hot pro

The most important feature of Callaway’s X2 Hot Pro irons for many golfers has nothing to do with their performance. It’s their price, $899, which makes them the cheapest players iron in the company’s 2014 lineup.

The main reason the X2 Hot Pro irons are $200 cheaper than Callaway’s other new players iron for 2014, the Apex Pro, is their construction. The X2 Hot irons are cast, a more cost-efficient way to make irons than the forging process used to make the Apex Pro irons. But just because an iron is cast doesn’t mean it can’t offer premium performance.

Screen Shot 2013-11-11 at 7.54.36 PM

The new irons lose the undercut cavity that was used on last year’s X Hot Pro irons, giving them a much more compact look. And like the Apex Pro irons, their soles are inspired by the popular soles on Callaway’s 2013 X Forged irons, giving the X2 Hot irons soles that are thicker in the center and thinner in the heel and toe to help better players improve their turf interaction.

callaway x2 hot pro

The X2 Hot Pro irons also have a stabilizing arch cast into their cavity, which helps give the irons more consistent ball speeds than last year’s model and also removes unwanted flexure of the irons’ toplines, contributing to irons’ better sound and feel.

Included also is Callaway’s CG Height progression, which moves weight lower in the long and mid irons for a higher launch and less spin, and higher in the short irons for a lower launch with more spin. The short irons also have less offset than the X Hot Pro short irons, giving them the cleaner look that many better players like to see from their short irons.

2c2ede804fb12bf1787d8a20c8ef635611fa801fe003b59cea2e018633b3a74362a4811975311a4ff08176da2093928a72879f7ac802e8383e90e0485b44368d

The X2 Hot Pro irons will be available Jan. 17. They have the same 37 wide-spaced V grooves as Callaway’s Apex Pro irons, and come stock with True Temper’s Project X 95 shaft, available in 5.5 (regular) and 6.0 (stiff) flexes.

Screen Shot 2013-11-11 at 8.02.12 PM

Click here to see what GolfWRX Members are saying about the X2 Hot and X2 Hot Pro irons, as well as the rest of the company’s X2 Hot lineup.

Your Reaction?
  • 183
  • LEGIT32
  • WOW31
  • LOL20
  • IDHT11
  • FLOP16
  • OB21
  • SHANK271

34 Comments

34 Comments

  1. steve parlak

    Apr 26, 2015 at 12:56 am

    where can i get a calloway x 2 hot 3 iron

  2. Jimbob

    Jul 10, 2014 at 12:19 am

    Little tip…It does not, repeat does not matter what an iron “looks” like or how low the lofts are. What does matter is how it performs for your swing PERIOD. Get off your high horses and come on out to the course where a 44* X2 Hot Pro PW will go further, and straighter than your super awesome, non-cheap looking, shiny, forever wearing, most workable, forged PGA tour only blades.

  3. Jeff

    Apr 16, 2014 at 8:51 pm

    I tried X Hot irons with graphite last fall and they weren’t enough to change. This Spring I traded my Razr X irons with Uniflex steel for X2 Hot irons with graphite to help with aging elbows. They are super hot, feel great on impact and their control beats my old Raz X irons. That’s hard to do! Over 50 years I have played my brands including Ping, Mizuno, Taylormade and Hogan. These remind me of my Hogan Edge irons I loved. Great club Callaway!

  4. Iron2850

    Feb 25, 2014 at 6:22 pm

    I hit these irons yesterday at a PGA Tour superstore. I hit both X2 Hot and the X2 Hot Pro’s vs. last years X Hot…last years clubs were lighter feeling, due the deep undercut cavity…this years model seems heavier in the head, easier to feel. I know the lofts are much different than what we are used to, but I hit these clubs much higher and longer than my Titleist AP1 712’s. I was hitting the X2 Hot 7 iron 170 and 26 yards high vs. the AP1 6 iron at 160 and 7 iron at 150, 18 yards high. I hit the X2 Hot 6 iron 180, 25 yards high. I am a notoriously low ball hitter which is why I am looking at these. Was hitting regular flex shafts in each club. Color doesn’t bother me much. Whether I hit them consistently (height and distance) are the most important variables to me. I would like to hear from anyone who has played these outdoors. AT $699 they allow Callaway to provide solid clubs at a lower price point than the Apex line. Thanks.

  5. Pingback: Callaway Golf Razr Xf Pitching Wedge

  6. marko

    Nov 16, 2013 at 2:20 am

    I dont get it? Forged clubs with a cast face. and clevelands cast clubs with a forged face. What is the difference in performance?

  7. Andrew

    Nov 13, 2013 at 6:16 pm

    This does not seem like Callaway’s best effort… very surprised.

    • Keith

      Mar 12, 2014 at 6:45 am

      Andrew I dont know why you would say that? The irons have a distinct look of the old X16-X18 irons from the top. After hitting the Apex Pro irons which I bought, I could not gedt them airborne. A mate of mine – a pro suggested to go back to a more cavity back Iron with a softer shaft. Which I did, the X Hot 2 irons with a regular shaft. And all I can say it was the best thing I ever did. Ball flight is sensational and easier an extra club longer. These things are great to hit, very easy. I am not a wood duck (4 marker) but im getting older so this has help slow my golf swing down, get into better positions at impact and boom.

  8. Joe

    Nov 13, 2013 at 5:19 pm

    I have played Callaway for more than a decade. I cannot believe the looks of the new irons! I wasn’t crazy about the new Apex/Apex Pro…but the new Hot line is terrible looking. Callaway has made such great improvements through the last 4 or 5 years…I am afraid that they have really gone backwards.

    Players won’t play ugly clubs…no matter how they perform.

  9. jgpl001

    Nov 13, 2013 at 4:42 pm

    These look cheap and Callaway have taken ten steps backwards

    Callaway you are going out of business if you keep this up – REALLY

    • marko

      Nov 16, 2013 at 2:15 am

      I have no idea what you guys are looking at? These irons look good and will sell like crazy.It’s all about performance. If they work they start to look good.

    • Keith

      Mar 12, 2014 at 6:49 am

      I could not care if they looked like shovels. They perform! They are long and the flight is high – amazing flight. Easily the most friendly set of clubs I have hit. Put them down and look at them. They look like the old Callaway’s which I loved. Once you see the flight, you would not care if they were pink.

  10. Jamie

    Nov 13, 2013 at 2:20 pm

    I hit the apex iron at the golf show in London, I have a set of Diablo forged with ozik had program shafts, they do not compare to the Diablo forged. The apex is just another offering to the market along with the x2 so callaway now mass produce products like taylormade, but if you hit the apex iron and have the chance to compar it to the legacy black, it’s night and day!!!
    The legacy black is a rolls Royce to the apex, x hot, x hot pro,
    Guess that’s why henrik stenson gamed them on route to the fed ex cup ,
    The apex and the x2 hot are just tweaked versions of the previous.

  11. Hiball

    Nov 13, 2013 at 1:05 pm

    Like every other club manufacturer, they tweak a iron from 6 months ago and everyone jumps on it. Think about it. Every driver is 5-10 yds longer than the previous model. Realty. I should be driving the ball 420. And the longer strong lofted irons? What a joke. You have such a huge gap from the pw to lw? But consumers buy into it. “I’m hitting my 6 iron 215” really? With a 4-5 length and loft. You all are suckers. And the manufactures thank you every year. What a joke.

    • KK

      Nov 13, 2013 at 11:39 pm

      So what irons do you play?? Wilson blades, Lynx Black Cats, Spalding, do your irons have wooden shafts? If by your theory, none of the latest iron offerings are improvements over their predecessors, no one should ever buy a new set of irons. If manufacturers never came out with new products, there wouldn’t be any reason for consumers to buy anything new. If all consumers thought like you, they wouldn’t ever buy anything new no matter how many different models manufacturers made. So who is right, you or the manufacturers?

  12. Ryan

    Nov 12, 2013 at 7:17 pm

    Nothing says “players iron” like a 45 degree pitching wedge.

  13. Santiago

    Nov 12, 2013 at 4:39 pm

    The problem with Callaway is Quality, I get why they are more profitable on their iron business, because they are cheap made. I bought the X Hot Pro and I can’t complain about their playability, they work great for me. But, i have owned them for 5 months and they wear so much, they already look worse than my 9 year old Taylormade RAC LT2 (My previous set) that I used a million times. The X-Hot Pro look like I have been hitting rocks every day since I got them. I clean my clubs after every round and I care about the way they look.
    I contacted them through Twitter and their answer was that this is perfectly normal. This is the first time I tried a Calaway product and for sure will be the last one, I will never waste my hard earned money on their cheap made products and their customer careless company.

    Some pics:
    2013 Callaway X-Hot Pro http://pic.twitter.com/rnkVFECQWQ
    2004 Taylormade RAC LT2 http://pic.twitter.com/5MdJSWpciM

    • Joe

      Nov 13, 2013 at 10:21 pm

      You’re probably a little misguided…basing everything on one experience. I have owned Callaways for years, and overall, have been very pleased, both with the high quality components and also design. I also own Titleist and TM stuff, and think they are all basically the same as far as quality.

    • Joe

      Nov 13, 2013 at 10:25 pm

      Also, I have RazrX forged that are 2 years old that don’t look nearly as aged as your XHots… I do understand your aggravation though.

    • james

      May 19, 2014 at 1:54 pm

      I have the exact same issue with Callaway XHot Pros series irons with one additional issue. The sole of my PW has cracked after only 6 months of play. No abuse, just golf. I’m 64 years old so I don’t slam my clubs into the ground, I don’t hit rocks etc. So, after very minimal use the PW has cracked and the clubs look 10 years old. I like the performance of the clubs but very poor quality club head material.

  14. Shawn

    Nov 12, 2013 at 2:53 pm

    My personal opinion is they hit it out of the park with the Apex line. I don’t see the reason for them to bring a competing club like the Xhot Pro to market? OEM needs to be careful with the iron lines and having to many products on the market.

    • Oldplayer

      Nov 13, 2013 at 2:34 pm

      Very different price point I imagine.

      • Shawn

        Nov 13, 2013 at 5:09 pm

        They said $200 dollar difference. I don’t think that substantial enough to buy a cast club over a forged product.

    • Keith

      Mar 12, 2014 at 6:53 am

      Shawn I hit both sets. The Apex and the X Hot 2 irons are completely different in feel. My honest opinion, the X Hot is better and a lot cheaper.

  15. Jon W

    Nov 12, 2013 at 11:57 am

    Copied Pings “Chevron”?

  16. Rich

    Nov 12, 2013 at 10:12 am

    Looks like the Wilson Staff M3 irons. Rather have the M3.

  17. B

    Nov 12, 2013 at 7:54 am

    Are Lefty’s going to miss out on the A Wedge again this Year!!!

  18. Jack

    Nov 12, 2013 at 2:19 am

    Interesting that they are not doing the cut cavity. Yet they are able to keep it just as forgiving.

  19. Paul

    Nov 12, 2013 at 1:17 am

    Pros look great, i sold my razr x tours and grabbed some titlesit CBs. Maybe should have waited for these…? Probably not.

  20. EM

    Nov 12, 2013 at 1:15 am

    X2Hot from the top line reminds me of Callaway clubs of old, like the X-series irons (12, 14, 16, etc) starting from more than a decade ago. Which is a good thing, as it will remind a lot of people of what they were using back in the day and bring them back to these clubs.

    The X2Hot Pros look awesome! They look really solid.

    • Keith

      Mar 12, 2014 at 6:55 am

      I Have a set, and could not agree with you more. Look like the X 16 but with longer and better flight. They are on a winner

  21. Soul

    Nov 12, 2013 at 1:11 am

    whoa the xhot pros are literally a club stronger than most players irons. I’m surprised they would do this with the xhot pros They sure look nice!!

    • Tyler

      Nov 12, 2013 at 11:18 am

      I think cuz they lowered the cg s much. Crazy though, 24 degree 5 iron.

Leave a Reply

Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Equipment

Coolest thing for sale in the GolfWRX Classifieds (4/18/24): Ping PLD Limited Anser – 1988 Open Championship – #2 of only 88 Made

Published

on

At GolfWRX, we are a community of like-minded individuals that all experience and express our enjoyment of the game in many ways.

It’s that sense of community that drives day-to-day interactions in the forums on topics that range from best driver to what marker you use to mark your ball. It even allows us to share another thing we all love – buying and selling equipment.

Currently, in our GolfWRX buy/sell/trade (BST) forum, there is a listing for a Ping PLD Limited Anser – 1988 Open Championship – #2 of only 88 Made.

From the seller: (@DLong72): “Ping PLD Limited Anser – 1988 Open Championship – #2 of only 88 Made. ?: $1150. ?? 100% milled collectors item from the limited releases commemorating when Ping putters won every major in 1988 (88 putters made). This was the model Seve Ballesteros used to win the 1988 Open Championship. Condition is brand new, never gamed, everything is in the original packaging as it came. Putter features the iconic sound slot.

Specs/ Additional Details

-100% Milled, Aluminum/Bronze Alloy (310g)

-Original Anser Design

-PING PP58 Grip

-Putter is built to standard specs.”

To check out the full listing in our BST forum, head through the link: Ping PLD Limited Anser – 1988 Open Championship – #2 of only 88 Made

This is the most impressive current listing from the GolfWRX BST, and if you are curious about the rules to participate in the BST Forum you can check them out here: GolfWRX BST Rules

Your Reaction?
  • 1
  • LEGIT0
  • WOW0
  • LOL0
  • IDHT0
  • FLOP0
  • OB0
  • SHANK0

Continue Reading

Equipment

Inside Collin Morikawa’s recent golf ball, driver, 3-wood, and “Proto” iron changes

Published

on

As you probably know by now, Collin Morikawa switched putters after the first round of The Masters, and he ultimately went on to finish T3.

The putter was far from the only change he made last week, however, and his bag is continuing to change this week at the 2024 RBC Heritage.

On the range of The Masters, Morikawa worked closely with Adrian Reitveld, TaylorMade’s Senior Manager of Tour at TaylorMade, to find the perfect driver and 3-wood setups.

Morikawa started off 2024 by switching into TaylorMade’s Qi10 Max driver, but since went back to his faithful TaylorMade SIM – yes, the original SIM from 2020. Somehow, some way, it seems Morikawa always ends up back in that driver, which he used to win the 2020 PGA Championship, and the 2021 Open Championship.

At The Masters, however, Rietveld said the duo found the driver head that allowed “zero compromise” on Morikawa’s preferred fade flight and spin. To match his preferences, they landed on a TaylorMade Qi10 LS 9-degree head, and the lie angle is a touch flatter than his former SIM.

“It’s faster than his gamer, and I think what we found is it fits his desired shot shape, with zero compromise” Rietveld told GolfWRX.com on Wednesday at the RBC Heritage.

Then, to replace his former SIM rocket 3-wood, Morikawa decided to switch into the TaylorMade Qi10 core model 13.5-degree rocket head, with an adjustable hosel.

“He likes the spin characteristics of that head,” Rietveld said. “Now he’s interesting because with Collin, you can turn up at a tournament, and you look at his 3-wood, and he’s changed the setting. One day there’s more loft on it, one day there’s less loft on it. He’s that type of guy. He’s not scared to use the adjustability of the club.

“And I think he felt our titanium head didn’t spin as low as his original SIM. So we did some work with the other head, just because he liked the feel of it. It was a little high launching, so we fit him into something with less loft. It’s a naughty little piece of equipment.” 

In addition to the driver and fairway wood changes, Morikawa also debuted his new “MySymbol” jersey No. 5 TP5x golf ball at The Masters. Morikawa’s choice of symbols is likely tied to his love of the Los Angeles Dodgers baseball team.

Not enough changes for you? There’s one more.

On Wednesday at the 2024 RBC Heritage, Morikawa was spotted with a new TaylorMade “Proto” 4-iron in the bag. If you recall, it’s the same model that Rory McIlroy debuted at the 2024 Valero Texas Open.

According to Morikawa, the new Proto 4-iron will replace his old P-770 hollow-bodied 4-iron.

“I used to hit my P-770 on a string, but sometimes the distance would be a little unpredictable,” Morikawa told GolfWRX.com. “This one launches a touch higher, and I feel I can predict the distance better. I know Rory replaced his P-760 with it. I’m liking it so far.” 

See Morikawa’s full WITB from the 2024 RBC Heritage here. 

Your Reaction?
  • 27
  • LEGIT2
  • WOW2
  • LOL4
  • IDHT2
  • FLOP3
  • OB3
  • SHANK2

Continue Reading

Equipment

Why Rory McIlroy will likely use the new TaylorMade BRNR Mini Driver Copper at the RBC Heritage

Published

on

Although we spotted Rory McIlroy testing the new TaylorMade BRNR Mini Driver Copper last week during practice rounds at the Masters, he ultimately didn’t decide to use the club in competition.

It seems that will change this week at the 2024 RBC Heritage, played at the short-and-tight Harbour Town Golf Links in Hilton Head.

When asked on Wednesday following his morning Pro-Am if he’d be using the new, nostalgic BRNR Copper this week, McIlroy said, “I think so.”

“I like it,” McIlroy told GolfWRX.com on Tuesday regarding the BRNR. “This would be a good week for it.”

 

View this post on Instagram

 

A post shared by GolfWRX (@golfwrx)

According to Adrian Rietveld, the Senior Manager of Tour at TaylorMade, the BRNR Mini Driver can help McIlroy position himself properly off the tee at the tight layout.

Here’s what Rietveld told GolfWRX.com on Wednesday:

“For someone like Rory, who’s that long at the top end of the bag, and then you put him on a course like Harbour Town, it’s tough off the tee. It’s tight into the greens, and you have to put yourself in position off the tee to have a shot into the green. It kind of reminds me of Valderrama in Spain, where you can be in the fairway and have no shot into the green.

“I’m caddying for Tommy [Fleetwood] this week, so I was walking the course last night and looking at a few things. There’s just such a small margin for error. You can be standing in the fairway at 300 yards and have a shot, but at 320 you don’t. So if you don’t hit a perfect shot, you could be stuck behind a tree. And then if you’re back at 280, it might be a really tough shot into the small greens.

“So for Rory [with the BRNR], it’s a nice course-specific golf club for him. He’s got both shots with it; he can move it right-to-left or left-to-right. And the main thing about this club has been the accuracy and the dispersion with it. I mean, it’s been amazing for Tommy.

“This was the first event Tommy used a BRNR last year, and I remember talking to him about it, and he said he couldn’t wait to play it at Augusta next year. And he just never took it out of the bag because he’s so comfortable with it, and hitting it off the deck.

“So you look at Rory, and you want to have the tools working to your advantage out here, and the driver could hand-cuff him a bit with all of the shots you’d have to manufacture.”

So, although McIlroy might not be making a permanent switch into the new TaylorMade BRNR Mini Driver Copper, he’s likely to switch into it this week.

His version is lofted at 13.5 degrees, and equipped with a Fujikura Ventus Black 7X shaft.

See more photos of Rory testing the BRNR Mini here

Your Reaction?
  • 25
  • LEGIT2
  • WOW0
  • LOL2
  • IDHT0
  • FLOP0
  • OB1
  • SHANK3

Continue Reading

WITB

Facebook

Trending